Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › from 2017.01
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0309752 AUTOMATIC HIGH BEAM SYSTEM U

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for Main Body: Body Electrical / Main Body / Data List.


ii.

for PCS/LDA/RSA/LVN: Chassis / PCS/LDA/ RSA/LVN / Data List.



e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Auto High Beam Main Switch Combination switch assembly (automatic high beam switch) signal / OFF or ON OFF: Combination switch assembly (automatic high beam switch) not pressed
ON: Combination switch assembly (automatic high beam switch) pressed
-
Dimmer SW Dimmer switch high position signal / OFF or ON OFF: Dimmer switch in low position
ON: Dimmer switch in high or high flash position
-
Auto Light SW Light control switch AUTO position signal / OFF or ON OFF: Light control switch not in AUTO position
ON: Light control switch in AUTO position
w/ Automatic Light Control System
Head Light SW (Head) Light control switch head position signal / OFF or ON OFF: Light control switch not in head position
ON: Light control switch in head position
-
Auto H Beam STS0 Automatic high beam sensor current state / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction*
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: system delay
Delay: Delay
Aim Lmt: Beam axis deviation
SAE Mode: Specialized detection
Undefin: Undefined
LIN Err: LIN malfunction
Auto H Beam STS1 Automatic high beam sensor state past 1 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction*
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: system delay
Delay: Delay
Aim Lmt: Beam axis deviation
SAE Mode: Specialized detection
Undefin: Undefined
LIN Err: LIN malfunction
Auto H Beam STS2 Automatic high beam sensor state past 2 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction*
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: system delay
Delay: Delay
Aim Lmt: Beam axis deviation
SAE Mode: Specialized detection
Undefin: Undefined
LIN Err: LIN malfunction
Auto H Beam STS3 Automatic high beam sensor state past 3 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction*
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: system delay
Delay: Delay
Aim Lmt: Beam axis deviation
SAE Mode: Specialized detection
Undefin: Undefined
LIN Err: LIN malfunction
Auto H Beam STS4 Automatic high beam sensor state past 4 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction*
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: system delay
Delay: Delay
Aim Lmt: Beam axis deviation
SAE Mode: Specialized detection
Undefin: Undefined
LIN Err: LIN malfunction
Auto H Beam STS5 Automatic high beam sensor state past 5 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction*
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: system delay
Delay: Delay
Aim Lmt: Beam axis deviation
SAE Mode: Specialized detection
Undefin: Undefined
LIN Err: LIN malfunction
Auto H Beam STS6 Automatic high beam sensor state past 6 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction*
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: system delay
Delay: Delay
Aim Lmt: Beam axis deviation
SAE Mode: Specialized detection
Undefin: Undefined
LIN Err: LIN malfunction
Auto H Beam STS7 Automatic high beam sensor state past 7 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction*
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: system delay
Delay: Delay
Aim Lmt: Beam axis deviation
SAE Mode: Specialized detection
Undefin: Undefined
LIN Err: LIN malfunction
Number of DTC Number of trouble codes / 0 to 255 Condition can be displayed -

*: If CAM NA is displayed, the lane departure warning camera may have stopped operating due to high temperature.



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / PCS/LDA/RSA/LVN / Active Test


e.

Perform Active Test according to the display on the GTS.

HINT:

The ignition switch must be turned to ON to proceed with the Active Test using the GTS.


PCS/LDA/RSA/LVN
Tester Display Test Part Control Range Diagnostic Note
Automatic High Beam Operates automatic high beam system ON / OFF This Active Test can only be performed when the ignition switch ON, the vehicle is stopped and the area around the vehicle is dark. (Normal system operation conditions, such as vehicle speed and shift lever position, do not need to be met.)