Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY › from 2017.01
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248416 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 81110B 1.REMOVE NO. 1 HEADLIGHT BULB (for Halogen Headlight)

a.
E366195

Remove the socket cover.


b.
E366196E01
0.958,1.531 1.083,1.698 0.125,0.167 10 true 2 2.219,1.698 2.344,1.865 0.125,0.167 10 true 1

Release the set spring in the direction indicated by the arrow in the order shown in the illustration.


c.
E366197

Remove the No. 1 headlight bulb.

NOTICE:

Do not touch the No. 1 headlight bulb glass.



Hide 81610F 2.REMOVE CLEARANCE LIGHT BULB (for Halogen Headlight)

a.
E366199

Turn the clearance light socket with the clearance light bulb as shown in the illustration to remove them as a unit.


b.
E366200

Remove the clearance light bulb from the clearance light socket.


Hide 81510C 3.REMOVE FRONT TURN SIGNAL LIGHT BULB (for Halogen Headlight)

a.
E366202

Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to remove them as a unit.


b.
E366203

Remove the front turn signal light bulb from the front turn signal light socket.


Hide 81510C 4.REMOVE FRONT TURN SIGNAL LIGHT BULB (for LED Headlight)

a.
E366204

Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to remove them as a unit.


b.
E366205

Remove the front turn signal light bulb from the front turn signal light socket.


Hide 85662 5.REMOVE HEADLIGHT LEVELING MOTOR (for Halogen Headlight)

a.
E423852

Turn the aiming screw as shown in the illustration.

HINT:

Make sure to remember the number of aiming screw rotations.



b.
E423853

Remove the headlight leveling motor as shown in the illustration.


Hide 85662 6.REMOVE HEADLIGHT LEVELING MOTOR (for LED Headlight)

a.
E423854

Turn the aiming screw as shown in the illustration.

HINT:

Make sure to remember the number of aiming screw rotations.



b.
E423855

Remove the headlight leveling motor as shown in the illustration.


Hide 85669 7.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.
E423856

Remove the headlight leveling motor base packing.

NOTICE:

The headlight leveling motor base packing must not be reused.



Hide 81136D 8.REMOVE HEADLIGHT COVER (for LED Headlight)

a.
E423857

Remove the headlight cover as shown in the illustration.


Hide 81171B 9.REMOVE HEADLIGHT LENS

a.

for LED Headlight:

i.
E423887

Disconnect the connector.

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)



b.
E423859

Remove the 6 screws.


c.
E423860

Using a dryer, warm the headlight lens gasket from the backside of the headlight assembly.

NOTICE:

If the headlight assembly is heated unevenly, it will deform or melt.



d.
E423861

Disengage the 7 claws to remove the headlight lens.


Hide 81132B 10.REMOVE HEADLIGHT LENS GASKET

a.
E423862

Remove the headlight lens gasket.

NOTICE:

The headlight lens gasket must not be reused.



Hide 81160A 11.REMOVE HEADLIGHT LED UNIT ASSEMBLY (for LED Headlight)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E423888

Disconnect the connector.


b.
E423864

Turn the aiming screw as shown in the illustration.

HINT:

Make sure to remember the number of aiming screw rotations.



c.
E423889

Disengage the 2 clamps to remove the headlight LED unit assembly.