Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY › from 2017.01
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248416 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the LH and RH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 81160A 1.INSTALL HEADLIGHT LED UNIT ASSEMBLY (for LED Headlight)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E423889

Engage the 2 clamps to install the headlight LED unit assembly.


b.
E423866

Turn the aiming screw as shown in the illustration to install the headlight LED unit assembly.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



c.
E423888

Connect the connector.


Hide 81132B 2.INSTALL HEADLIGHT LENS GASKET

a.

Clean the installation groove of the headlight lens sub-assembly.


b.
E237693C18
1.063,0.438 1.385,0.208 false 0.927,1.323 1.25,1.094 false 0.802,1.333 1.115,1.531 0.313,0.198 10 false *a 1.458,0.125 1.771,0.323 0.313,0.198 10 false *b 1.542,0.531 1.698,0.729 0.156,0.198 10 false 1 0.26,0.688 0.417,0.885 0.156,0.198 10 false 2
*a Release Paper
*b Tape


Partially remove the release paper from a new headlight lens gasket, and cut off a piece of it.


c.

Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.


d.

Cut the headlight lens gasket as shown in the illustration.


e.
E423867C01
0.875,2.927 1.188,3.083 0.313,0.156 10 false *a
*a 20 mm (0.787 in.) or more


Starting from the position shown in the illustration and moving clockwise, temporarily install the headlight lens gasket as shown in the illustration.


f.

Using screwdriver with their tips wrapped with release paper, completely press the headlight lens gasket into the straight groove to install it.

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly.




g.

The headlight lens gasket overlaps itself 20 mm (0.787 in.) or more.


h.

Check the installation condition of the headlight lens gasket.

NOTICE:
·

Make sure the headlight lens gasket is not protruding and is installed properly.

·

Make sure there is no gap between the ends of the headlight lens gasket.

·

Make sure to thoroughly check the corners as the headlight lens gasket is likely to be improperly installed in the corners.




Hide 81171B 3.INSTALL HEADLIGHT LENS

a.

Clean the sealing surface of the headlight lens.


b.
E423861

Engage the 7 claws to install the headlight lens.


c.
E423859

Install the 6 screws.


d.

for LED Headlight:

i.
E423887

Connect the connector.

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)



Hide 81136D 4.INSTALL HEADLIGHT COVER (for LED Headlight)

a.
E423868

Install the headlight cover as shown in the illustration.


Hide 85669 5.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING

a.
E423856

Install a new headlight leveling motor base packing.


Hide 85662 6.INSTALL HEADLIGHT LEVELING MOTOR (for Halogen Headlight)

a.
E423870

Install the headlight leveling motor as shown in the illustration.


b.
E423869

Turn the aiming screw as shown in the illustration.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



Hide 85662 7.INSTALL HEADLIGHT LEVELING MOTOR (for LED Headlight)

a.
E423872

Install the headlight leveling motor as shown in the illustration.


b.
E423871

Turn the aiming screw as shown in the illustration.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



Hide 81510C 8.INSTALL FRONT TURN SIGNAL LIGHT BULB (for Halogen Headlight)

a.
E366207

Install the front turn signal light bulb to the front turn signal light socket.


b.
E366208

Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to install them as a unit.


Hide 81510C 9.INSTALL FRONT TURN SIGNAL LIGHT BULB (for LED Headlight)

a.
E366209

Install the front turn signal light bulb into the front turn signal light socket.


b.
E366210

Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to install them as a unit.


Hide 81610F 10.INSTALL CLEARANCE LIGHT BULB (for Halogen Headlight)

a.
E366211

Install the clearance light bulb into the clearance light socket.


b.
E366212

Turn the clearance light socket with the clearance light bulb as shown in the illustration to install them as a unit.


Hide 81110B 11.INSTALL NO. 1 HEADLIGHT BULB (for Halogen Headlight)

a.
E366197

Install the No. 1 headlight bulb.

NOTICE:

Do not touch the No. 1 headlight bulb glass.



b.
E366215E01
2.167,1.802 2.354,1.969 0.188,0.167 10 true (2) 0.792,1.417 0.979,1.583 0.188,0.167 10 true (1)

Lock the set spring in the direction indicated by the arrow in the order shown in the illustration.


c.
E366195

Install the socket cover.