Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH › from 2017.01
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248424 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY (w/ Pre-crash Safety System)

a.
E368911C02
1.417,0.167 1.917,0.417 0.5,0.25 0.917,1.833 1.292,1.198 true 2.167,1.833 2.042,1.198 true 2.417,1.833 2.271,1.208 true 1.542,0.219 2,0.417 0.458,0.198 10 false A92 0.781,1.875 1.24,2.073 0.458,0.198 10 false GND 2.146,1.885 2.365,2.073 0.219,0.188 10 false B 2.396,1.885 2.615,2.073 0.219,0.188 10 false B 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A92-7 (B) - A92-2 (GND) Ignition switch on 11 to 14 V
A92-6 (B) - A92-2 (GND) Ignition switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A92-2 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.


c.
E233300C70
1.427,0.271 1.917,0.563 0.49,0.292 1.927,1.115 2.406,1.677 true 2.094,1.115 2.896,1.677 true 1.813,1.115 1.99,1.677 true 1.688,1.115 1.167,1.677 true 0.188,0.115 0.417,0.281 0.229,0.167 10 false *a 1.542,0.333 1.99,0.594 0.448,0.26 10 false A92 2.854,1.698 3.302,1.917 0.448,0.219 10 false OUT 2,1.708 2.313,1.917 0.313,0.208 10 false L 2.302,1.698 2.802,1.917 0.5,0.219 10 false GND 1,1.698 1.448,1.958 0.448,0.26 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Connect the stop light switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A92- 1 (OUT) - A92-2 (GND) Brake pedal not depressed Below 1 V
A92-1 (OUT) - A92-2 (GND) Brake pedal depressed 11 to 14 V
A92-3 (L) - A92-2 (GND) Brake pedal not depressed Below 1 V
A92-3 (L) - A92-2 (GND) Brake pedal depressed 11 to 14 V
A92-4 (ACC) - A92-2 (GND) Ignition switch off 11 to 14 V


If the result is not as specified, replace the stop light switch assembly.


Hide 84340 2.INSPECT STOP LIGHT SWITCH ASSEMBLY (w/o Pre-crash Safety System)

a.
B420140C04
1.5,0.333 1.948,0.563 0.448,0.229 0.917,1.729 1.292,1.448 true 1.594,1.927 1.688,1.479 true 2.385,1.885 2.115,1.458 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.594,0.365 1.906,0.563 0.313,0.198 10 false A91 0.854,1.76 1.094,1.958 0.24,0.198 10 false B 2.375,1.927 2.615,2.125 0.24,0.198 10 false B 1.479,1.948 1.865,2.146 0.385,0.198 10 false GND
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-1 (B) - A91-3 (GND) Always 11 to 14 V
A91-5(B) - A91-3(GND) Ignition switch on (IG) 11 to 14 V


If the result is not as specified, repair or replace the wire harness or connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-3 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.


d.
B420141C04
1.5,0.365 1.948,0.604 0.448,0.24 0.948,1.656 1.552,1.208 true 1.302,1.865 1.719,1.219 true 2.229,1.823 1.875,1.208 true 0.042,0.052 0.354,0.25 0.313,0.198 10 false *a 1.594,0.406 1.906,0.604 0.313,0.198 10 false A91 0.896,1.698 1.208,1.896 0.313,0.198 10 false L 2.26,1.875 2.573,2.073 0.313,0.198 10 false L 1.188,1.917 1.5,2.115 0.313,0.198 10 false GND
*a Component with harness connected
(Stop Light Switch Assembly)


Connect the stop light switch assembly connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-2 (L) - A91-3 (GND) Brake pedal not depressed Below 1 Ω
A91-2 (L) - A91-3 (GND) Brake pedal depressed 11 to 14 V
A91-4 (L) - A91-3 (GND) Brake pedal not depressed 11 to 14 V
A91-4 (L) - A91-3 (GND) Brake pedal depressed Below 1 Ω


If the result is not as specified, replace the stop light switch assembly.