READ DATA LIST
Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P-Seatbelt Buckle SW | Front passenger side seat belt buckle signal / OFF or ON | OFF: Front passenger side seat belt unfastened
ON: Front passenger side seat belt fastened |
- |
| 2nd-Row Seatbelt Buckle (R) | Rear seat belt buckle RH signal / ON or OFF | ON: Rear seat belt RH fastened
OFF: Rear seat belt RH unfastened |
- |
| 2nd-Row Seatbelt Buckle (L) | Rear seat belt buckle LH signal / ON or OFF | ON: Rear seat belt LH fastened
OFF: Rear seat belt LH unfastened |
- |
| 2nd-Row Seatbelt Buckle (C) | Rear seat center belt buckle signal / ON or OFF | ON: Rear seat center belt fastened
OFF: Rear seat center belt unfastened |
- |
| Driver Side Seatbelt Warning Buzzer | Driver side seat belt warning buzzer signal / OFF or ON | OFF: Seat belt warning buzzer disabled
ON: Seat belt warning buzzer enabled |
The current customize setting is displayed. |
| P - Seatbelt Warning Buzzer | Front passenger side seat belt warning buzzer signal / OFF or ON | OFF: Seat belt warning buzzer disabled
ON: Seat belt warning buzzer enabled |
The current customize setting is displayed. |
| Rear Seatbelt Warning Buzzer | Rear seat belt warning buzzer signal / ON or OFF | ON: Seat belt warning buzzer enabled
OFF: Seat belt warning buzzer disabled |
The current customize setting is displayed. |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Door Courtesy SW | Rear door RH courtesy light switch signal / ON or OFF | ON: Rear door RH opened
OFF: Rear door RH closed |
- |
| RL Door Courtesy SW | Rear door LH courtesy light switch signal / ON or OFF | ON: Rear door LH opened
OFF: Rear door LH closed |
- |
| D Seat Buckle SW | Driver side seat belt buckle signal / OFF or ON | OFF: Driver side seat belt unfastened
ON: Driver side seat belt fastened |
- |
| FR Door Courtesy | Front door courtesy light switch RH signal / ON or OFF | ON: Front door RH opened
OFF: Front door RH closed |
- |
| FL Door Courtesy | Front door courtesy light switch LH signal / ON or OFF | ON: Front door LH opened
OFF: Front door LH closed |
- |
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Combination Meter / Active Test.
According to display on the GTS, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Driver side seat belt warning light | OFF/ON | Confirm that the vehicle is stopped and the engine is idling. |