Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2018.06
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0307822 PRE-CRASH SAFETY SYSTEM D

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  SYSTEM DESCRIPTION  


PRE-CRASH SAFETY SYSTEM DESCRIPTION


a.

The pre-crash safety system determines the possibility of a collision according to information such as the position of the obstacle and its relative speed, and provides optimal control to avoid the collision and control to reduce the impact during the collision via warnings, brake assist and automatic braking.



FUNCTION OF COMPONENTS


Component Function
Pre-crash Safety City Sensor
·

Acquires information about a preceding vehicle or pedestrian from a monocular camera sensor and laser sensor to perform pre-crash safety system control.

·

Sends the information display, PCS warning light (PCS OFF indicator) and PCS activation indicator signal to the combination meter assembly based on pre-crash safety system control information.

·

Sounds the meter buzzer based on pre-crash safety system control information.

·

Operates the pre-crash safety city heater to remove condensation from the part of the windshield in front of the pre-crash safety city sensor.


Pre-crash Safety System Cancel Switch Assembly Stops and starts the pre-crash safety system and changes the warning timing.
Combination Meter Assembly
·

Displays the pre-crash safety system control status (ON/OFF) and warning timing.

·

During a system malfunction, warns the driver by blinking the PCS warning light (PCS OFF indicator) and sounding the meter buzzer.

·

Sounds the meter buzzer according to signals from the pre-crash safety city sensor.


ECM
·

Detects the shift position signal and accelerator opening angle and sends that information to the pre-crash safety city sensor.

·

Performs engine output control based on information from the pre-crash safety city sensor.


Brake Actuator Assembly (Skid Control ECU)
·

Sends information such as the vehicle speed signal, stop light switch signal and brake control hydraulic pressure to the pre-crash safety city sensor.

·

Performs brake hydraulic pressure and emergency brake signal control based on information from the pre-crash safety city sensor.


Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) Detects the steering angle and steering direction.
Airbag ECU Assembly (Yaw Rate Sensor) Detects the yaw rate and acceleration of the vehicle and transmits signals to the pre-crash safety city sensor.
Main Body ECU (Multiplex Network Body ECU) Sends destination information to the pre-crash safety city sensor.
VSC OFF Switch Disables the pre-crash brake and pre-crash brake assist operation when the switch is turned on.


OUTLINE OF PRE-CRASH SAFETY DETECTION


a.

Collision detection

i.

The system determines in advance the possibility of a collision and whether the collision can be avoided based on road surface conditions and the position and speed of the preceding vehicle or pedestrian according to information about the preceding vehicle or pedestrian from the pre-crash safety city sensor.

HINT:

For details about the system, see "OUTLINE OF PRE-CRASH SAFETY SYSTEM CONTROL" and the function descriptions.



ii.

Component

Component Detection Content
Pre-crash safety city sensor Obstacle in front (vehicle or pedestrian)




OUTLINE OF PRE-CRASH SAFETY SYSTEM CONTROL


Control Condition Start of Control Sender ECU Receiver ECU Operated Parts
Pre-crash warning Collision is possible Pre-crash safety city sensor Combination meter assembly
·

Combination meter assembly (PCS activation indicator)

·

Meter buzzer (warning sound)


Pre-crash brake assist Collision is highly possible Pre-crash safety city sensor
·

Combination meter assembly

·

Brake actuator assembly (skid control ECU)


·

Combination meter assembly (PCS activation indicator)

·

Brake actuator assembly (skid control ECU)

·

Meter buzzer (warning sound)


Pre-crash brake Possibility of a collision is very high Pre-crash safety city sensor
·

Combination meter assembly

·

Brake actuator assembly (skid control ECU)

·

ECM


·

Combination meter assembly (PCS activation indicator)

·

Brake actuator assembly (skid control ECU)

·

ECM

·

Meter buzzer (warning sound)




PRE-CRASH ALARM CONTROL


a.

When the system determines that there is a risk of colliding with an obstacle in front of the vehicle or pedestrian, the PCS activation indicator and the pre-crash safety city buzzer are used to warn the driver to avoid the collision.



PRE-CRASH BRAKE ASSIST CONTROL


a.

When the system determines that there is a risk of colliding with an obstacle in front of the vehicle or pedestrian, brake assist enters standby status and the hydraulic brake pressure is increased to improve braking effectiveness when the driver depresses the brake pedal.



PRE-CRASH BRAKE CONTROL


a.

When the system determines that the possibility of a frontal collision with the vehicle or pedestrian is high, the brakes are operated to reduce the collision speed and reduce the impact during the collision.

NOTICE:

When the system detects that the driver is attempting to cancel operation of the system by performing operations such as the following, pre-crash brake control is canceled.

·

Accelerator pedal is forcefully depressed

·

Steering wheel is operated quickly to avoid a collision




b.

Turning the VSC OFF switch on disables pre-crash brake assist control and pre-crash brake control.

HINT:

After pressing the switch, the PCS warning light (PCS OFF indicator) in the combination meter assembly will illuminate.




PRE-CRASH SAFETY SYSTEM (PCS) OPERATION CONDITIONS


a.

The pre-crash alarm control, pre-crash brake assist control and pre-crash brake control can operate if all of the following conditions are met:

·

Pre-crash safety system is on

·

PCS warning light (PCS OFF indicator) in combination meter assembly does not blink

·

Shift lever is not in R



b.

If the following conditions are met, the pre-crash alarm control will operate:

·

Vehicle speed is approximately 15 to 140 km/h (10 to 85 mph) (When a pedestrian is detected, vehicle speed is approximately 15 to 65 km/h (10 to 40 mph)).

·

The relative speed between your vehicle and the vehicle or pedestrian ahead is greater than approximately 15 km/h (10 mph).



c.

If the following conditions are met, the pre-crash brake assist control will operate:

·

Vehicle speed is approximately 30 to 80 km/h (20 to 50 mph) (When a pedestrian is detected, vehicle speed is approximately 30 to 65 km/h (20 to 40 mph)).

·

The relative speed between your vehicle and the vehicle or pedestrian ahead is greater than approximately 30 km/h (20 mph).

·

VSC system is not disabled



d.

If the following conditions are met, the pre-crash brake control will operate:

·

Vehicle speed is approximately 10 to 80 km/h (7 to 50 mph) (When a pedestrian is detected, vehicle speed is approximately 10 to 65 km/h (7 to 40 mph)).

·

The relative speed between your vehicle and the vehicle or pedestrian ahead is greater than approximately 10 km/h (7 mph).

·

VSC system is not disabled




OUTLINE OF PRE-CRASH SAFETY CITY HEATER


a.

The pre-crash safety city heater can operate if all of the following conditions are met:

·

No pre-crash safety system DTCs are stored

·

Engine running



b.

If either of the following conditions are met, the pre-crash safety city heater will operate:

·

Ambient temperature (detected by air conditioning system) is 5°C (41°F) or lower

·

Vehicle is being driven when ambient temperature is 5 to 20°C (41 to 68°F) and area of windshield in front of pre-crash safety city sensor begins to fog (blockage of pre-crash safety city sensor detected)



c.

If the following condition is met, the pre-crash safety city heater will stop operating:

·

30 minutes have elapsed since pre-crash safety city heater operation began




Situations in which the system may not operate properly


a.

In some situations such as the following, an object may not be detected by the pre-collision city sensor, preventing the system from operating properly:

·

When a detectable object is approaching your vehicle

·

When your vehicle or a detectable object is wobbling

·

If a detectable object makes an abrupt maneuver (such as sudden swerving, acceleration or deceleration)

·

When your vehicle approaches a detectable object rapidly

·

When a detectable object is not directly in front of your vehicle

·

When a detectable object is near a wall, fence, guardrail, manhole cover, vehicle, steel plate on the road, etc.

·

When part of a detectable object is hidden by an object, such as large baggage, an umbrella, or guardrail

·

When multiple detectable objects are close together

·

If the sun or other light is shining directly on a detectable object

·

When a detectable object is a shade of white and looks extremely bright

·

When a detectable object appears to be nearly the same color or brightness as its surroundings

·

If a detectable object cuts or suddenly emerges in front of your vehicle

·

When the front of your vehicle is hit by water, snow, dust, etc.

·

When a very bright light ahead, such as the sun or the headlights of oncoming traffic, shines directly into the pre-collision city sensor

·

When approaching the side or front of a vehicle ahead

·

If a vehicle ahead is narrow, such as a personal mobility vehicle

·

If a preceding vehicle has a small rear end, such as an unloaded truck

·

If a preceding vehicle has a low rear end, such as a low bed trailer

·

If a vehicle ahead has extremely high ground clearance

·

If a vehicle ahead is carrying a load which protrudes past its rear bumper

·

If a vehicle ahead is irregularly shaped, such as a tractor or side car

·

If a pedestrian ahead is shorter than approximately 3.2 ft. (1 m) or taller than approximately 6.5 ft. (2 m)

·

If a pedestrian is wearing oversized clothing (a rain coat, long skirt, etc.), making their silhouette obscure

·

If a pedestrian is bending forward or squatting

·

If a pedestrian is moving fast

·

If a pedestrian is pushing a stroller, wheelchair, bicycle or other vehicle

·

When driving in inclement weather such as heavy rain, fog, snow or a sandstorm

·

When driving through steam or smoke

·

When the surrounding area is dim, such as at dawn or dusk, or while at night or in a tunnel, making a detectable object appear to be nearly the same color as its surroundings

·

When driving in a place where the surrounding brightness changes suddenly, such as at the entrance or exit of a tunnel

·

While driving on a curve and for a few seconds after driving on a curve

·

If your vehicle is skidding

·

If the front of the vehicle is raised or lowered

·

If the wheels are misaligned

·

If a wiper blade is blocking the pre-collision city sensor

·

The vehicle is being driven at extremely high speeds

·

When driving on a hill

·

When a detectable object is a poor reflector of laser

·

If the pre-collision city sensor is misaligned



b.

In some situations such as the following, sufficient braking force may not be obtained, preventing the system from performing properly:

·

If the braking functions cannot operate to their full extent, such as when the brake parts are extremely cold, extremely hot, or wet

·

If the vehicle is not properly maintained (brakes or tires are excessively worn, improper tire inflation pressure, etc.)

·

When the vehicle is being driven on a gravel road or other slippery surface




Conditions under which the system may operate even if there is no possibility of a collision


a.

In the following situations the sensor may detect an object, causing the system to determine that there is a possibility of a frontal collision and operate.

·

When passing a detectable object, etc.

·

When changing lanes while overtaking a detectable object, etc.

·

When passing an oncoming vehicle while making a left or right turn

·

When approaching a detectable object in an adjacent lane or on the roadside, such as when changing the course of travel or driving on a winding road

·

When rapidly closing on a detectable object, etc.

·

When approaching objects on the roadside, such as detectable objects, guardrails, utility poles, trees, or walls

·

When there is a detectable object or other object by the roadside at the entrance of a curve

·

When there are patterns or paint in front of your vehicle that may be mistaken for a detectable object

·

When the front of your vehicle is hit by water, snow, dust, etc.

·

When overtaking a detectable object that is changing lanes or making a right/left turn

·

When passing a detectable object in an oncoming lane that is stopped to make a right/left turn

·

When a detectable object approaches very close and then stops before entering the path of your vehicle

·

If the front of your vehicle is raised or lowered, such as when on an uneven or undulating road surface

·

When driving on a road surrounded by a structure, such as in a tunnel or on an iron bridge

·

When there is a metal object (manhole cover, steel plate, etc.), steps, or a protrusion in front of your vehicle

·

When passing under an object (road sign, billboard, etc.)

·

When approaching an electric toll gate barrier, parking area barrier, or other barrier that opens and closes

·

When using an automatic car wash

·

When driving through or under objects that may contact your vehicle, such as thick grass, tree branches, or a banner

·

When driving through steam or smoke

·

When the front part of the vehicle is raised or lowered

·

When the pre-collision city sensor is misaligned due to a strong impact being applied to the pre-collision city sensor, etc.

·

When the vehicle is being parked in a place where there is a low hanging object at the height of the pre-collision city sensor

·

When the windshield is dirty or covered with raindrops, condensation, ice, snow, etc.




If the PCS warning light illuminates or blinking and a warning message is displayed on the multi-information display


HINT:

For details on the operation of the PCS warning light and displayed warning messages, refer to Diagnosis System.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>FAIL-SAFE CHART


a.

The pre-collision system may be temporarily unavailable or there may be a malfunction in the system.


b.

In the following situations, the PCS warning light will turn off, the message will disappear and the system will become operational when normal operating conditions return:

·

When the pre-collision city sensor or the area around pre-collision city sensor is hot, such as in the sun

·

When the part of the windshield glass in front of the pre-collision city sensor is fogged up or covered with condensation or ice

·

When the pre-collision city sensor or the area around pre-collision city sensor is cold, such as in an extremely cold environment

·

If the pre-collision city sensor is obstructed, such as when the hood is open or a sticker is attached to the windshield near the pre-collision city sensor




PRE-CRASH SAFETY SYSTEM AUTOMATIC CANCELLATION


a.

When a system malfunction is detected and the sensor cannot detect vehicles, system operation cancels automatically.

HINT:

When the system malfunctions or is temporarily disabled, the PCS warning light (PCS OFF indicator) blink or illuminate.