Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Sedan)

AIRBAG SYSTEM (for Sedan) > PRECAUTION


CAUTION:
  1. The vehicle is equipped with a Supplemental Restraint System (SRS), which consists of a driver airbag, front passenger airbag, and front seat belt pretensioners. Failure to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Furthermore, if a mistake is made in servicing the SRS, it is possible that the SRS may fail to operate when required. Before performing servicing (including removal or installation of parts, inspection or replacement), be sure to read the following items carefully, then follow the correct procedures as indicated in the repair manual.
  2. Wait at least 90 seconds after the ignition switch is turned off and the negative (-) terminal cable is disconnected from the battery before starting the operation.
    (The SRS is equipped with a back-up power source, so if work is started within 90 seconds of disconnecting the negative (-) terminal cable of the battery, the SRS may be deployed).
  3. Do not directly expose the steering pad, front passenger airbag assembly, center airbag sensor assembly, front airbag sensor LH, front airbag sensor RH, front seat inner belt assembly LH, seat position sensor, occupant classification ECU, front seat outer belt assembly LH or front seat outer belt assembly RH to hot air or flames.

NOTICE:
  1. Malfunction symptoms of the SRS are difficult to confirm, so DTCs are the most important source of information when troubleshooting. When troubleshooting the SRS, always inspect DTCs before disconnecting the battery.
  2. Even in the case of a minor collision when the SRS does not deploy, the following parts should be inspected.
    1. Steering pad
    2. Front passenger airbag assembly
    3. Center airbag sensor assembly
    4. Front airbag sensor LH
    5. Front airbag sensor RH
    6. Front seat inner belt assembly LH
    7. Seat position sensor
    8. Occupant classification ECU
    9. Front seat outer belt assembly LH
    10. Front seat outer belt assembly RH
  3. Before commencing repair work, remove the airbag sensor if any kind of shock is likely to occur to the airbag sensor during the operation.
  4. Never use SRS parts from another vehicle. When replacing parts, replace them with new ones.
  5. Never disassemble or repair any of the following parts in order to reuse them. If any of these parts have been dropped, or a defect is found (e.g. cracks, dents or any other defects) in any of the housings, brackets or connectors, then replace the part with a new one.
    1. Steering pad
    2. Front passenger airbag assembly
    3. Center airbag sensor assembly
    4. Front airbag sensor LH
    5. Front airbag sensor RH
    6. Front seat inner belt assembly LH
    7. Seat position sensor
    8. Occupant classification ECU
    9. Front seat outer belt assembly LH
    10. Front seat outer belt assembly RH
  6. Use a volt/ohmmeter with high impedance (10 kΩ/V minimum) for troubleshooting the electrical circuits.
  7. Information labels are attached to the periphery of the SRS components. Follow the instructions in the cautions.
  8. After work on the SRS is completed, perform the SRS warning light check (Click here).
  9. When the negative (-) terminal cable is disconnected from the battery, the memory will be cleared. Therefore make a record of the contents stored in each system before starting work. When the work is finished, reset each system as it was before. Never use a back-up power supply from outside the vehicle to avoid erasing the memory in any system.
  10. If the vehicle is equipped with a mobile communication system, refer to the precautions in the INTRODUCTION section.

HINT:
In the airbag system, the center airbag sensor assembly, front airbag sensor LH and RH are collectively referred to as the airbag sensors.


1.HANDLING PRECAUTIONS FOR AIRBAG SENSORS
  1. Before starting the following operations, wait for at least 90 seconds after disconnecting the negative (-) terminal cable from the battery:

    1. Replacement of the airbag sensors

  2. When connecting or disconnecting the airbag sensor connectors, ensure that each sensor is installed in the vehicle.

  3. Do not use the airbag sensors which have been dropped during the operation or transportation.

  4. Do not disassemble the airbag sensors.


2.INSPECTION PROCEDURE FOR VEHICLE INVOLVED IN ACCIDENT
  1. When the airbag has not deployed, confirm the DTCs by checking the SRS warning light. If there is any malfunction in the SRS airbag system, perform troubleshooting.

  2. When any of the airbags have deployed due to the collision, be sure to replace all sensors in the damaged areas and center airbag sensor assembly.