STEERING PAD (for Hatchback) > DISPOSAL |
![]() |
| 1. DISPOSE OF STEERING PAD (When Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery.
Connect the red clip of SST to the positive (+) battery terminal.
Connect the black clip of SST to the negative (-) battery terminal.
| *1 | Battery |
![]() |
Press SST activation switch, and check that the LED of SST activation switch comes on.
Disconnect SST from the battery.
Read the precaution (Click here).
Disconnect the cable from the negative (-) battery terminal.
Remove the lower steering column cover .
![]() |
Disconnect the airbag connector, as shown in the illustration.
| *1 | Slider |
Install SST.
![]() |
Connect SST.
![]() |
Move SST to at least 10 m (33 ft.) away from the vehicle front side window.
| *1 | Battery |
Maintaining enough clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
Press SST activation switch to deploy the airbag.
![]() |
Dispose of the steering pad.
| *1 | Plastic Bag |
Remove the steering pad from the steering wheel.
Place the steering pad in the plastic bag, tie it tightly and dispose of it according to local regulations.
| 2. DISPOSE OF STEERING PAD (When not Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery.
Connect SST to the battery. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
| *1 | Battery |
![]() |
Press SST activation switch, and check that the LED of SST activation switch comes on.
Disconnect SST from the battery.
Remove the steering pad (Click here).
![]() |
Using braided wire harness, tie down the steering pad to an unneeded wheel.
| *a | Stripped Wire Harness Section |
| Area | Measurement |
| A | 1.25 mm2 or more (0.00192 in.2 or more) |
Wind 3 wires at least 3 times each around each of the snap pins.

| *1 | Disc Wheel | *2 | Tire |
| *a | Secure Airbag with Deployment Surface Facing Up | *b | 3 times or more |
Face the airbag deployment side of the steering pad upward on top of an unneeded tire and wheel set. Separately tie each side of the steering pad to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.
![]() |
Install SST.
Connect the SST connector.
![]() |
Move SST at least 10 m (33 ft.) away from the airbag tied down to the wheel.
![]() |
Cover the steering pad (using a cardboard box).
| *1 | Weight |
Cover the steering pad with a cardboard box.
Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).
| Area | Measurement |
| X | 460 mm (1.51 ft.) |
| Y | 650 mm (2.13 ft.) |
![]() |
Cover the steering pad (using tires).
| *a | Inner Diameter |
| *b | Width |
| *c | Tires (3 or more) |
Place at least 3 tires without wheels onto the wheel and tire to which the steering pad is tied.
Place a wheel and tire on top.
| Area | Measurement |
| Inner diameter | 360 mm (14.17 in.) |
| Width | 185 mm (7.28 in.) |
![]() |
Tie the tires together with the 2 wires.
![]() |
Deploy the airbag.
| *A | Using a Cardboard Box |
| *B | Using Tires |
| *1 | Battery |
| *2 | Steering Pad |
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Check that no one is within a 10 m (33 ft.) radius of the wheel to which the steering pad is tied.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the steering pad.
| *1 | Plastic Bag |
Remove the steering pad from the wheel.
Place the steering pad in a plastic bag, tie it tightly and dispose of it according to local regulations.