Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0110    Intake Air Temperature Circuit Malfunction

DTC    P0112    Intake Air Temperature Circuit Low Input

DTC    P0113    Intake Air Temperature Circuit High Input


DESCRIPTION

A067628E12
  1. The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
  2. The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

    HINT:
    When any of DTCs P0110, P0112 and P0113 are stored, the ECM enters fail-safe mode. During fail-safe mode, the IAT is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No.
DTC Detection Condition
Trouble Area
P0110
Open or short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM
P0112
Short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Short in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM
P0113
Open in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM

HINT:
When any of these DTCs are stored, check the IAT by entering the following menus on the Techstream: Powertrain / Engine and ECT / Intake Air.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit


WIRING DIAGRAM


A112566E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Intake Air.

  1. Read the value displayed on the Techstream.

    OK:
    Same as actual Intake Air Temperature (IAT).


    Result 
    Temperature Displayed
    Proceed To
    -40 °C (-40°F)
    A
    140°C (284°F) or higher
    B
    Same as actual IAT
    C

    HINT:
    1. If there is an open circuit, the Techstream indicates -40°C (-40°F).
    2. If there is a short circuit, the Techstream indicates 140°C (284°F) or higher.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
A107690E06
  1. Disconnect the C26 Mass Air Flow (MAF) meter connector.

  1. Connect terminals THA and E2 of the MAF meter wire harness side connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard Value:
    140°C (284°F) or higher

  1. Reconnect the MAF meter connector.



NG
Go to step 3
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER (Click here)  

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A107856E02
  1. Disconnect the C26 MAF meter connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    THA (C26-4) - THA (C20-65)
    Below 1 Ω
    E2 (C26-5) - ETHA (C20-88)

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM (Click here)  

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
A084869E25
  1. Disconnect the C26 MAF meter connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard Value:
    -40°C (-40°F)

  1. Reconnect the MAF meter connector.



NG
Go to step 5
OK

REPLACE MASS AIR FLOW METER (Click here)  

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A107856E03
  1. Disconnect the C26 MAF meter connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    THA (C26-4) or THA (C20-65) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)