DTC P0101 Mass Air Flow Circuit Range / Performance Problem |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0101 | Conditions (a), (b), (c), (d) and (e) are met (2 trip detection logic): (a) The engine is running. (b) The engine coolant temperature is 70°C (158°F) or higher. (c) The throttle position sensor voltage is 0.24 V or higher, and less than 2 V. (d) The average engine load value ratio is less than 0.85, or more than 1.19 (varies with estimated engine load). Average engine load value ratio = Average engine load based on mass air flow meter output / Average engine load estimated from driving conditions (e) The average air fuel ratio is less than -20% or more than 20%. |
|
| Related DTCs | P0101: Mass Air Flow Meter Rationality |
| Required Sensors/Components (Main) | Mass air flow meter |
| Required Sensors/Components (Related) | Crankshaft position sensor Camshaft position sensor Engine coolant temperature sensor Throttle position sensor |
| Frequency of Operation | Continuous |
| Duration | 10 times |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Throttle position (throttle position sensor voltage) | 0.24 V or higher, and less than 2 V |
| Time after engine start | 5 seconds or more |
| Battery voltage | 10.5 V or higher |
| Estimated load | 30% or higher, and less than 70% |
| Engine coolant temperature | 70°C (158°F) or higher |
| Mass air flow meter circuit fail (P0102, P0103) | Not detected |
| Intake air temperature circuit fail (P0112, P0113) | Not detected |
| Engine coolant temperature circuit fail (P0115, P0117, P0118) | Not detected |
| Crankshaft position sensor circuit fail (P0335) | Not detected |
| Throttle position sensor circuit fail (P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135) | Not detected |
| EVAP system pressure sensor circuit fail (P0452, P0453) | Not detected |
| Leak detection pump fail (P2401, P2402) | Not detected |
| EVAP vent valve fail (P2419, P2420) | Not detected |
| Both of following conditions 1 and 2 met | - |
| 1. Average engine load value ratio | Less than 0.85 or more than 1.19 (varies with estimated engine load) |
| 2. Average air fuel ratio | Less than -20% or more than 20% |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0101) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0101 is output | A |
| DTC P0101 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks .
|
| ||||
| OK | |
| 3.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 4.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0101.
Check the DTC judgment.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||