Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P2102    Throttle Actuator Control Motor Circuit Low

DTC    P2103    Throttle Actuator Control Motor Circuit High


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.
The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle with motor body assembly. The TP sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No.
DTC Detection Condition
Trouble Area
P2102
Conditions (a) and (b) continue for 2.0 seconds:
(1 trip detection logic)
(a) Throttle actuator duty ratio 80 % or more
(b) Throttle actuator current less than 0.5 A
  1. Open in throttle actuator circuit
  2. Throttle actuator
  3. ECM
P2103
Either of following conditions met :
(1 trip detection logic)
  1. Hybrid IC diagnosis signal fail
  2. Hybrid IC current limiter port fail
  1. Short in throttle actuator circuit
  2. Throttle actuator
  3. Throttle valve
  4. Throttle body
  5. ECM


FAIL-SAFE

When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts off the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned to OFF.

WIRING DIAGRAM


A112572E01


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  1. The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Open Duty / Throttle Motor Close Duty) can be read using the Techstream. However the ECM shuts off the throttle actuator current when the ETCS malfunctions.

1.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
A059778E82
  1. Disconnect the C17 throttle with motor body assembly connector.

  1. Measure the resistance of the throttle actuator.

    Standard resistance:
    Tester Connections
    Specified Conditions
    M+ (2) - M- (1)
    0.3 to 100 Ω at 20°C (68°F)

  1. Reconnect the throttle with motor body assembly connector.



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)
A115662E49
  1. Disconnect the C17 throttle with motor body assembly connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    M+ (C17-2) - M+ (C20-42)
    Below 1 Ω
    M- (C17-1) - M- (C20-41)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    M+ (C17-2) or M+ (C20-42) - Body ground
    10 kΩ or higher
    M- (C17-1) or M- (C20-41) - Body ground

  1. Reconnect the throttle with motor body assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check for foreign objects between the throttle valve and the housing.

    OK:
    No foreign objects between throttle valve and housing.



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY
OK


4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
  1. Check if the throttle valve opens and closes smoothly.

    OK:
    Throttle valve opens and closes smoothly.



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)