DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2120 | VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). |
|
| P2122 | VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). |
|
| P2123 | VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic). |
|
| P2125 | VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). |
|
| P2127 | VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). |
|
| P2128 | Both of the following conditions continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or higher. (b) VPA is between 0.4 V and 3.45 V. |
|
| P2138 | Either of the following conditions continues for 2.0 seconds or more (1 trip detection logic): (a) The difference between VPA and VPA2 is 0.02 V or less. (b) VPA is 0.4 V or less and VPA2 is 1.2 V or less. |
|
| Trouble Area | Accelerator Pedal Released | Accelerator Pedal Depressed | ||
| Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | |
| Open in VCP circuit | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.75 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| Open in EPA circuit | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.75 V |
| Related DTCs | P2120: Accelerator Pedal Position Sensor 1 Range Check (Fluctuating) P2122: Accelerator Pedal Position Sensor 1 Range Check (Low Voltage) P2123: Accelerator Pedal Position Sensor 1 Range Check (High Voltage) P2125: Accelerator Pedal Position Sensor 2 Range Check (Fluctuating) P2127: Accelerator Pedal Position Sensor 2 Range Check (Low Voltage) P2128: Accelerator Pedal Position Sensor 2 Range Check (High Voltage) P2138: Accelerator Pedal Position Sensor Range Check (Correlation) |
| Required Sensors/Components (Main) | Accelerator pedal sensor assembly |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P2120, P2122, P2125 and P2127 2.0 seconds: P2123, P2128 and P2138 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Either of following conditions met: | - |
| Time after ignition switch OFF to ON | 0.012 seconds or more |
| Command to electronic throttle actuator power | ON |
| Either of following conditions met: | 1 or 2 |
| 1. All of following conditions met: | (a) and (b) |
| (a) VPA voltage | 0.4 V or less |
| (b) VPA2 voltage - Learned VPA2 accelerator off position voltage | 0.04 V or higher |
| 2. VPA voltage | 4.8 V or higher |
| All of following conditions met: | (a) and (b) |
| (a) VPA voltage | 0.4 V or less |
| (b) VPA2 voltage - Learned VPA2 accelerator off position voltage | 0.04 V or higher |
| VPA voltage | 4.8 V or higher |
| Either of following conditions met: | 1 or 2 |
| 1. All of following conditions met: | (a) and (b) |
| (a) VPA2 voltage | 1.2 V or less |
| (b) VPA voltage - Learned VPA accelerator off position voltage | 0.04 V or higher |
| 2. VPA2 voltage when VPA voltage 0.4 to 3.45 V | 4.8 V or higher |
| All of following conditions met: | (a) and (b) |
| (a) VPA2 voltage | 1.2 V or less |
| (b) VPA voltage - Learned VPA accelerator off position voltage | 0.04 V or higher |
| VPA2 voltage when VPA voltage 0.4 to 3.45 V | 4.8 V or higher |
| Either of following conditions met: | Condition A or B |
| Condition A | - |
| Difference between VPA and VPA 2 voltages | 0.02 V or less |
| Condition B | - |
| VPA voltage | 0.4 V or less |
| VPA2 voltage | 1.2 V or less |
| VPA voltage | Higher than 0.4 V, and less than 4.8 V |
| VPA2 voltage | Higher than 1.2 V, and less than 4.8 V |
| Difference between VPA and VPA2 voltages | Higher than 0.02 V |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the value displayed on the Techstream.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V | More than 0.02 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 4.75 V |
| *a | Depressed |
| *b | Released |
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM) |
Disconnect the A64 accelerator pedal sensor assembly connector.
Disconnect the A72 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A64-6 (VPA) - A72-51 (VPA) | Always | Below 1 Ω |
| A64-5 (EPA) - A72-52 (EPA) | Always | Below 1 Ω |
| A64-4 (VCPA) - A72-53 (VCPA) | Always | Below 1 Ω |
| A64-3 (VPA2) - A72-54 (VPA2) | Always | Below 1 Ω |
| A64-2 (EPA2) - A72-55 (EPA2) | Always | Below 1 Ω |
| A64-1 (VCP2) - A72-56 (VCP2) | Always | Below 1 Ω |
| A64-6 (VPA) or A72-51 (VPA) - Body ground | Always | 10 kΩ or higher |
| A64-5 (EPA) or A72-52 (EPA) - Body ground | Always | 10 kΩ or higher |
| A64-4 (VCPA) or A72-53 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A64-3 (VPA2) or A72-54 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A64-2 (EPA2) or A72-55 (EPA2) - Body ground | Always | 10 kΩ or higher |
| A64-1 (VCP2) or A72-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A64-4 (VCPA) - A64-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| A64-1 (VCP2) - A64-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Accelerator Pedal Sensor Assembly) |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY |
Replace the accelerator pedal sensor assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||