DTC P0335 Crankshaft Position Sensor "A" Circuit |
DTC P0339 Crankshaft Position Sensor "A" Circuit Intermittent |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0335 | When any of following conditions is met when camshaft position sensor circuit fail is not detected: (1 trip detection logic)
|
|
| P0339 | Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic): (a) Engine speed 1000 rpm or more (b) Starter signal OFF (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF |
|
![]() |
| ECM Terminal Name | CH1: Between VV1+ and NE- CH2: Between NE+ and NE- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Cranking or idling |
| Related DTCs | P0335: Crankshaft position sensor range check/rationality P0335: Crankshaft position sensor verify pulse input |
| Required Sensors/Components (Main) | Crankshaft position sensor |
| Required Sensors/Components (Related) | Camshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | -: Verify pulse input case 1 4.7 seconds: Verify pulse input case 2 0.016 seconds: Range check/rationality |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| All of the following conditions are met | - |
| Ignition switch | ON |
| Time after starter off to on | 3 seconds or more |
| Number of camshaft position sensor signal pulses | 6 times |
| Battery voltage | 7 V or higher |
| Minimum battery voltage while starter on | Less than 11 V |
| Camshaft position sensor circuit fail (P0340) | Not detected |
| All of the following conditions are met | - |
| Starter | OFF |
| Engine speed (Top dead sensor) | 600 rpm or higher |
| Engine speed (30°CA) | 600 rpm or higher |
| Time after starter from on to OFF | 3 seconds or more |
| Both of the following conditions are met | - |
| Starter | ON |
| Minimum battery voltage while starter ON | Below 11 V |
| Number of crankshaft position sensor signal pulses | 87 times or less, or 220 times or more |
| Engine speed signal | No signal |
| Crankshaft position sensor |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (ENGINE SPEED) |
Connect a Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
Read the values displayed on the Techstream while the engine is running.
|
| ||||
| OK | ||
| ||
| 2.INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C52-1 - C51-78 (NE+) | Always | Below 1 Ω |
| C52-2 - C51-110 (NE-) | Always | Below 1 Ω |
| C52-1 or C51-78 (NE+) - Body ground | Always | 10 kΩ or higher |
| C52-2 or C51-110 (NE-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() |
Check the crankshaft position sensor installation.
|
| ||||
| OK | |
| 5.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE) |
Check the teeth of the crank angle sensor plate.
|
| ||||
| OK | |
| 6.REPLACE CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 OR P0339) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Read DTCs.
| Result | Proceed to |
| DTC is not output (No pending DTCs output) | A |
| DTC P0335 or P0339 is output | B |
|
| ||||
| A | ||
| ||