Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM (for Hatchback)

POWER DOOR LOCK CONTROL SYSTEM (for Hatchback) > All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder


DESCRIPTION

The main body ECU receives switch signals from the door control switch, and driver door key cylinder or front passenger door key cylinder switch signals from the front door lock with motor assembly LH or front door lock with motor assembly RH. The main body ECU activates the door lock motor on each door according to these signals.

WIRING DIAGRAM


B289462E01


INSPECTION PROCEDURE

1.CHECK DOOR LOCK OPERATION
  1. Check door lock operation (Click here).
    Result 
    Result
    Proceed to
    All doors cannot be locked through door control switch
    A
    All doors cannot be locked through door key cylinder
    B



B
Go to step 5
A


2.READ VALUE USING TECHSTREAM (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door manual lock switch signal / OFF or ON
    OFF: Door control switch is turned to unlock position
    ON: Door control switch is turned to lock position
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / OFF or ON
    OFF: Door control switch is turned to lock position
    ON: Door control switch is turned to unlock position
    -

    OK:
    The Techstream indicates ON or OFF according to the switch operation shown in the table above.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (Click here)  

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Inspect the power window regulator master switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU)
  1. Disconnect the D143 main body ECU connector.

  1. Disconnect the G20*1 or G22*2 power window regulator master switch assembly (door control switch) connector.

    1. *1: w/ Power Window
    2. *2: w/o Power Window

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 5 Door with Power Window 
    Tester Connection
    Condition
    Specified Condition
    G20-2 (L) - D143-9 (L1)
    Always
    Below 1 Ω
    G20-9 (UL) - D143-10 (UL1)
    Always
    Below 1 Ω
    G20-1 (E) - Body ground
    Always
    Below 1 Ω
    D143-9 (L1) - Body ground
    Always
    10 kΩ or higher
    D143-10 (UL1) - Body ground
    Always
    10 kΩ or higher
    for 3 Door with Power Window 
    Tester Connection
    Condition
    Specified Condition
    G20-1 (L) - D143-9 (L1)
    Always
    Below 1 Ω
    G20-9 (UL) - D143-10 (UL1)
    Always
    Below 1 Ω
    G20-7 (E) - Body ground
    Always
    Below 1 Ω
    D143-9 (L1) - Body ground
    Always
    10 kΩ or higher
    D143-10 (UL1) - Body ground
    Always
    10 kΩ or higher
    w/o Power Window 
    Tester Connection
    Condition
    Specified Condition
    G22-4 (L) - D143-9 (L1)
    Always
    Below 1 Ω
    G22-2 (UL) - D143-10 (UL1)
    Always
    Below 1 Ω
    G22-3 (E) - Body ground
    Always
    Below 1 Ω
    D143-9 (L1) - Body ground
    Always
    10 kΩ or higher
    D143-10 (UL1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (Click here)  

5.CHECK DOOR LOCK OPERATION (DOOR KEY CYLINDER)
  1. Proceed to the next step according to the symptom if all the doors cannot be locked/unlocked at once.
    Result 
    Result
    Proceed to
    All doors cannot be locked/unlocked at once by using door key cylinder on driver door.
    A
    All doors cannot be locked/unlocked at once by using door key cylinder on front passenger door.
    B
    All doors cannot be locked/unlocked at once by using both driver door and front passenger door key cylinder.
    C



B
Go to step 9

C
REPLACE MAIN BODY ECU (Click here)
A


6.READ VALUE USING TECHSTREAM (DOOR LOCK AND UNLOCK SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver door and front passenger door lock and unlock switch signal / OFF or ON
    OFF: Driver door or front passenger door key cylinder not turned
    ON: Driver door or front passenger door key cylinder turned to lock position
    -
    D Door key SW-Unlock
    Driver door lock and unlock switch signal / OFF or ON
    OFF: Driver door key cylinder not turned
    ON: Driver door key cylinder turned to lock position
    -

    OK:
    The Techstream indicates ON or OFF according to the key cylinder operation shown in the table.



NG
Go to step 7
OK

REPLACE MAIN BODY ECU (Click here)  

7.INSPECT FRONT DOOR LOCK ASSEMBLY LH
  1. Inspect the front door lock assembly LH (Click here).



NG
REPLACE FRONT DOOR LOCK ASSEMBLY LH (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY LH - MAIN BODY ECU)
  1. Disconnect the D143 main body ECU connector.

  1. Disconnect the G23 front door lock assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G23-9 (L) - D143-11 (L2)
    Always
    Below 1 Ω
    G23-10 (UL) - D143-24 (UL3)
    Always
    Below 1 Ω
    G23-7 (E) - Body ground
    Always
    Below 1 Ω
    D143-11 (L2) - Body ground
    Always
    10 kΩ or higher
    D143-24 (UL3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (Click here)  

9.READ VALUE USING TECHSTREAM (DOOR LOCK AND UNLOCK SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver door and front passenger door lock and unlock switch signal / OFF or ON
    OFF: Driver door or front passenger door key cylinder not turned
    ON: Driver door or front passenger door key cylinder turned to lock position
    -
    Door Key SW-Unlock
    Front passenger door lock and unlock switch signal / OFF or ON
    OFF: Front passenger door key cylinder not turned
    ON: Front passenger door key cylinder turned to unlock position
    -

    OK:
    The Techstream indicates ON or OFF according to the key cylinder operation shown in the table.



NG
Go to step 10
OK

REPLACE MAIN BODY ECU (Click here)  

10.INSPECT FRONT DOOR LOCK ASSEMBLY RH
  1. Inspect the front door lock assembly RH (Click here).



NG
REPLACE FRONT DOOR LOCK ASSEMBLY RH (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY RH - MAIN BODY ECU)
  1. Disconnect the D143 main body ECU connector.

  1. Disconnect the F23 front door lock assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F23-6 (L) - D143-11 (L2)
    Always
    Below 1 Ω
    F23-5 (UL) - D143-12 (UL2)
    Always
    Below 1 Ω
    F23-8 (E) - Body ground
    Always
    Below 1 Ω
    D143-11 (L2) - Body ground
    Always
    10 kΩ or higher
    D143-12 (UL2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (Click here)