Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER (for Hatchback)

FRONT SUSPENSION MEMBER (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE MOVING CONTROL ROD
  1. Install the engine moving control rod with the bolt.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }

    HINT:
    Temporarily tighten the transaxle side, and then tighten the bolt to the specified torque.



2. INSTALL ENGINE MOVING CONTROL ROD COVER (for Cold Area)
  1. Install the engine moving control rod cover with the 2 clips.



3. TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH
  1. Install the front lower suspension arm sub-assembly LH with the bolt.



4. TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



5. INSTALL FRONT STABILIZER BAR


6. INSTALL FRONT NO. 1 STABILIZER BRACKET LH


    C229644E01
  1. Provisionally tighten bolt A.

  1. Tighten the bolts to the specified torque, in the order of B then A.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



7. INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:
Use the same procedure for the RH side as for the LH side.



8. INSTALL MANUAL STEERING GEAR
  1. Install the manual steering gear onto the front suspension crossmember with the 2 bolts and 2 nuts.

    Torque:
    79 N*m{ 800 kgf*cm , 58 ft.*lbf }

    NOTICE:
    Keep the nut from rotating while turning the bolt.



9. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C233132
  1. Place wooden blocks or plate lift attachments on an engine lifter, and then set the front suspension crossmember sub-assembly so that the attachments are in the positions shown in the illustration.
    Text in Illustration 
    V100135
    Front of the Vehicle
    V100144
    Attachment Placement Positions

  1. Provisionally install the front suspension crossmember sub-assembly onto the body with the 6 bolts.



  1. By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.


    C233133E01


    Text in Illustration 
    *a
    Datum Hole
    -
    -
    V100135
    Front of the Vehicle
    -
    -
    SST
    09670-00011  
    09670-00020  

    Torque:
    Bolt A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    Bolt B:
    151 N*m{ 1540 kgf*cm , 111 ft.*lbf }
    Bolt C:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    1. Insert SST into the datum hole in a vertical orientation.
    2. If SST cannot be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.

  1. Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



10. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.



11. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



12. INSTALL TIE ROD END SUB-ASSEMBLY LH
  1. Install the tie rod end sub-assembly onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.



13. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



14. INSTALL FRONT STABILIZER LINK ASSEMBLY LH
  1. Install the front stabilizer link assembly LH with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    Using a socket hexagon wrench 6 to hold the stud.



15. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



16. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
  1. Install clip B onto the body portion and install the No. 1 steering column hole cover onto the body portion with clip A.

    NOTICE:
    Make sure that the lip portion of steering column hole cover is not damaged.



17. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY


    C245426E02
  1. Align the matchmarks and install the steering sliding yoke sub-assembly onto the manual steering gear.
    Text in Illustration 
    *1
    Steering Sliding Yoke Sub-assembly
    *a
    Matchmarks

  1. Install the bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



18. INSTALL COLUMN HOLE COVER SILENCER SHEET
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



19. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



20. POSITION WHEELS FACING STRAIGHT AHEAD


21. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



22. FULLY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH


C107515E05
  1. Fully tighten the 2 bolts.

    Torque:
    Bolt A:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }
    Bolt B:
    151 N*m{ 1540 kgf*cm , 111 ft.*lbf }



23. FULLY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



24. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


25. CHECK SPEED SENSOR SIGNAL (w/ ABS)
(Click here)


26. CHECK SPEED SENSOR SIGNAL (w/ VSC)
(Click here)