FRONT PASSENGER AIRBAG ASSEMBLY (for Hatchback) > DISPOSAL |
| 1. DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Disconnect the cable from the negative (-) battery terminal.
Remove the instrument cluster finish panel garnish assembly .
Install SST to the instrument panel wire inflator side.
![]() |
Pull the slider in the direction indicated by the arrow to release the lock and disconnect the 2 airbag connectors.
| *1 | Slider |
| *2 | Airbag Connector |
| *3 | Vent Hole Connector |
Connect SST connector to the instrument panel wire airbag connector side.
Check that the lock slider is in the lock position.
![]() |
Connect SST connector.
Close all doors.
![]() |
Move SST at least 10 m (33 ft.) away from the vehicle front side window.
| *1 | Battery |
Deploy the instrument panel passenger airbag assembly inflator.
Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
Press SST activation switch and deploy the airbag.
Install SST to the instrument panel wire vent hole connector side.
![]() |
Pull the slider in the direction indicated by the arrow to release the lock and disconnect SST connector from the instrument panel wire airbag connector side.
| *1 | Slider |
Connect SST connector to the instrument panel wire vent hole connector side.
![]() |
Connect SST connector.
Deploy the front passenger airbag actuator.
Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
Press SST activation switch and deploy the actuator.
| 2. DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY INFLATOR (When not Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Remove the instrument panel passenger airbag assembly (Click here).
Connect SST.
![]() |
Connect the 2 SST connectors to the instrument panel passenger airbag assembly inflator.
| *1 | Locking Button |
Push in the locking button.
![]() |
Using a braided wire harness, tie the instrument panel passenger airbag assembly to a tire.
| *a | Stripped Wire Harness Section |
| Area | Measurement |
| A | 1.25 mm2 or more (0.00192 in.2 or more) |
Position the instrument panel passenger airbag assembly inside a tire with the airbag deployment side facing inside.

| Area | Measurement |
| A | 360 mm (14.17 in.) |
| B | 185 mm (7.28 in.) |
![]() |
Place tires.
| *1 | Tires (2 or more) |
Place at least 2 tires under the tire which the instrument panel passenger airbag assembly is tied to.
Place at least 2 tires over the tire which the instrument panel passenger airbag assembly is tied to. The top tire should have a disc wheel installed.
![]() |
Tie the tires together with 2 wire harnesses.
Install SST.
![]() |
Connect SST connector.
| *1 | Battery |
Deploy the instrument panel passenger airbag assembly inflator.
Check that no one is within a 10 m (33 ft.) radius of the tire which the instrument panel passenger airbag assembly is tied to.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Press SST activation switch and deploy the airbag.
Disconnect the red clip of SST from the positive (+) battery terminal and the black clip of SST from the negative (-) battery terminal.
| 3. DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY ACTUATOR (When not Installed in Vehicle) |
Connect SST connector.
Check that the tires used when deploying the instrument panel passenger airbag assembly inflator are not damaged.
Check that the wire harnesses used to tie the instrument panel passenger airbag assembly are not severed.
Disconnect the 2 SST connectors from the instrument panel passenger airbag assembly inflator.
![]() |
Connect SST connector to the instrument panel passenger airbag assembly actuator.
| *1 | Locking Button |
Push in the locking button.
Install SST.
![]() |
Connect SST connector.
| *1 | Battery |
Deploy the instrument panel passenger airbag assembly actuator.
Check that no one is within a 10 m (33 ft.) radius of the tire which the instrument panel passenger airbag assembly is tied to.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) terminal.
Press SST activation switch and deploy the airbag.
![]() |
Dispose of the instrument panel passenger airbag assembly.
| *1 | Plastic Bag |
Remove the lower instrument panel passenger airbag assembly from the tire.
Place the lower instrument panel passenger airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.