Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM (for Sedan)

POWER DOOR LOCK CONTROL SYSTEM (for Sedan) > Key Lock-in Prevention Function does not Work Properly


DESCRIPTION

When the key is in the ignition key cylinder or the door courtesy light ON signal is output to the main body ECU, performing the door lock operation with the lock switch does not lock the doors.

HINT:
Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with How to Proceed with Troubleshooting. Then, conduct the following troubleshooting procedure.


WIRING DIAGRAM


B117142E06


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on tester, read on the "Data List".


Main Body:

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Courtesy SW
Driver side door courtesy switch signal / ON or OFF
ON: Driver side door is open
OFF: Driver side door is closed
-

OK:
The display is as specified in the normal condition.



NG
Go to step 5
OK


2.READ VALUE USING TECHSTREAM
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on tester, read on the "Data List".


Main Body:

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Key Unlock Warning SW
Unlock warning switch signal / ON or OFF
ON: Key is in ignition key cylinder
OFF: No key is in ignition key cylinder
-

OK:
The display is as specified in the normal condition.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY


    B117144E02
  1. Remove the unlock warning switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩor higher
    1 - 2
    Pushed
    Below 1 Ω



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU)


    B121085E01
  1. Disconnect the D19 unlock warning switch connector.

  1. Disconnect the 4D main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D19-1 - 4D-7 (KSW)
    Below 1 Ω
    D19-2 - Body ground
    Below 1 Ω

  1. Reconnect the unlock warning switch connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

5.INSPECT FRONT DOOR COURTESY SWITCH ASSEMBLY (DRIVER SIDE)


    B129185E01
  1. Remove the door courtesy switch.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Not pushed (ON)
    Below 1 Ω
    1 - Body ground
    Pushed (OFF)
    10 kΩor higher

  1. Reinstall the courtesy switch.



NG
REPLACE FRONT DOOR COURTESY SWITCH ASSEMBLY (DRIVER SIDE) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH - MAIN BODY ECU)


    B112021E10
  1. Disconnect the J2 door courtesy switch connector.

  1. Disconnect the 4A main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    J2-1 - 4A-21 (DCTY)
    Below 1 Ω

  1. Reconnect the door courtesy switch connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU