BACK DOOR GLASS (for Hatchback) > INSTALLATION |
| 1. CLEAN BACK DOOR GLASS |
![]() |
Using a scraper, remove the adhesive sticking to the back door glass.
Clean the outer edge of the back door glass with a non-residue solvent.
| 2. INSTALL BACK WINDOW GLASS CLIP RH |
Apply Primer G to the installation part of the back window glass clip.
![]() |
Install a new clip onto the glass, as shown in the illustration.
| *a | Back Side |
| 3. INSTALL BACK WINDOW GLASS CLIP LH |
Apply Primer G to the installation part of the back window glass clip.
![]() |
Install a new clip onto the glass, as shown in the illustration.
| *a | Back Side |
| 4. INSTALL BACK WINDOW GLASS ADHESIVE DAM |
Using a brush or sponge, coat the application area of adhesive dam with Primer G.
Install a new adhesive dam onto the back door glass, as shown in the illustration.

| *a | Back Side | *b | 6.9 mm (0.273 in.) |
| 5. INSTALL BACK DOOR GLASS |
![]() |
Clean and shape the contact surface of the vehicle body.
| *1 | Adhesive |
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.
![]() |
Position the back door glass.
| *a | Mark |
Using suction cups, place the back door glass in the correct position.
Align the matchmarks on the back door glass and vehicle body.
Remove the back door glass.
![]() |
Using a brush, coat the installation surface on the vehicle body with Primer M.
| *1 | Primer M |
| *2 | Adhesive |
| *a | Correct |
| *b | Incorrect |
Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.

| *1 | Primer G | - | - |
| *a | Back Side | *b | 14.0 mm (0.551 in.) |
| *c | 22.0 mm (0.866 in.) | *d | 45.3 mm (1.783 in.) |
Apply adhesive to the glass.
![]() |
Cut off the tip of the cartridge nozzle, as shown in the illustration.
| *a | 8.0 mm (0.315 in.) |
| *b | 12.0 mm (0.472 in.) |
| Temperature | Tack-free Time |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with a cartridge.
Apply adhesive to the back door glass, as shown in the illustration.

| *1 | Adhesive | - | - |
| *a | Back Side | *b | 14.5 mm (0.571 in.) |
| *c | 12.0 mm (0.472 in.) | *d | 8.0 mm (0.315 in.) |
| *e | 52.3 mm (2.059 in.) | - | - |
Install the back door glass.
![]() |
Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.
| *a | Mark |
Lightly press the front surface of the back door glass to ensure a close fit.
![]() |
If necessary, use a scraper to correct the level or position of adhesive that has been applied.
| *1 | Back Door Glass |
| *2 | Dam |
| *3 | Adhesive |
Hold the back door glass using protective tape until applied adhesive hardens.
| Temperature | Minimum Time Prior to Driving Vehicle |
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
Connect the 2 connectors.
| 6. INSPECT FOR LEAK AND REPAIR |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 7. INSTALL BACK DOOR PANEL NO. 2 PROTECTOR |
![]() |
Using a piece of cloth or similar material, rub off any double-sided tape remaining on the back door panel.
| *1 | Double-sided Tape |
Using a non-residue solvent, clean the attachment surface.
Remove the double-sided tape backing of the new back door panel protector.
Install the back door panel No. 2 protector with 2 clips.
| 8. INSTALL BACK DOOR PANEL NO. 1 PROTECTOR |
| 9. INSTALL REAR WIPER MOTOR GROMMET (w/ Rear Wiper) |
![]() |
Apply MP grease to the entire surface of the rear wiper motor grommet lip.
![]() | Lip of Rear Wiper Motor Grommet |
| 10. INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper) |
for TMC Made:
![]() |
Set the rear wiper motor assembly in place and temporarily tighten the bolt A.
Temporarily tighten the 2 bolts B.
Fully tighten the 3 bolts in the order shown in the illustration.
Connect the connector.
for TMMF Made:
![]() |
Install the rear wiper motor assembly with the 3 bolts in the order shown in the illustration.
Connect the connector.
| 11. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper) |
![]() |
Operate the wiper and stop the rear wiper motor at the automatic stop position.
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
| *a | Wire Brush |
| *b | Wiper Arm Serration |
| *c | Wiper Pivot Serration |
![]() |
Install the rear wiper arm and blade assembly with the nut to the position as shown in the illustration.
| *a | Mark for Blade Position |
Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.
| 12. INSTALL REAR WIPER ARM HEAD CAP (w/ Rear Wiper) |
Engage the 2 claws and 2 hinges, to install the rear wiper arm head cap.
| 13. INSTALL BACK DOOR TRIM BOARD |
![]() |
Engage the 11 clips and install the back door trim board.
| 14. INSTALL REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler) |