AUTOMATIC TRANSAXLE SYSTEM (for Hatchback) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
In accordance with the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| N Range Status | Judgment for shift lever N position/ OFF or ON |
| - |
| Neutral Position SW Signal | Park/neutral position switch status/ OFF or ON |
| When shift lever position displayed on Techstream differs from actual position, adjustment of Park/neutral position switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/ OFF or ON |
| - |
| SPD (NT) | Input turbine speed/ display: 50 rpm Min.: 0 rpm Max.: 12750 rpm |
| - |
| Shift SW Status (P Range) | Park/neutral position switch status/ OFF or ON |
| When shift lever position displayed on Techstream differs from actual position, adjustment of Park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | Park/neutral position switch status/ OFF or ON |
| |
| Shift SW Status (2 Range) | Park/neutral position switch status/ OFF or ON |
| |
| Shift SW Status (L Range) | Park/neutral position switch status/ OFF or ON |
| |
| Shift SW Status (N Range) | Park/neutral position switch status/ OFF or ON |
| |
| Shift SW Status (N,P Range) Supported | Shift lever position P or N support status/ Supp or Unsupp |
| - |
| Shift SW Status (N,P Range) | Park/neutral position switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of Park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (D Range) | Park/neutral position switch status/ OFF or ON |
| |
| Shift SW Status (3 Range) | Park/neutral position switch status/ OFF or ON |
| |
| A/T Oil Temperature 1 | ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If the value is "-40°C (-40°F)" or "150°C (302°F) or more", ATF temperature sensor circuit is opened or shorted. |
| Lock Up | Lock up status/ OFF or ON |
| - |
| ST Solenoid Status | Shift solenoid ST status/ OFF or ON | OFF → ON → OFF: Up-shifting and down-shifting between 3rd and 4th gears while driving | - |
| Shift Status | Actual gear Position/ 1st, 2nd, 3rd or 4th | Same as actual gear | - |
| SLT Solenoid Status | Shift solenoid SLT status/ OFF or ON |
| - |
| SLU Solenoid Status | Shift solenoid SLU status/ OFF or ON |
| - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Select the following items: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLU) | [Test Details] Operate shift solenoid SLU | OFF/ON | [Vehicle Condition]
|
| Activate the Solenoid (SLT)* | [Test Details] Operate shift solenoid SLT and raise the line pressure.
| OFF/ON | [Vehicle Condition]
|
| Activate the Solenoid (S1) | [Test Details] Operate shift solenoid S1 | OFF/ON | [Vehicle Condition]
|
| Activate the Solenoid (S2) | [Test Details] Operate shift solenoid S2 | OFF/ON | [Vehicle Condition]
|
| Activate the Lock Up | [Test Details] Control shift solenoid SLU to set automatic transaxle to lock-up condition. | OFF/ON | Possible to check SLU operation. [Vehicle Condition] Vehicle speed: 60 km/h (36 mph) or more, and 4th gear |
| Control the Shift Position | [Test Details] Operate shift solenoid valve and set each shift position manually. [Others]
| 1st/2nd/3rd/4th | Possible to check operation of shift solenoid valves. [Vehicle Condition] Vehicle speed: Less than 50 km/h (30 mph) |
| Activate the Solenoid (ST) | [Test Details] Operate shift solenoid ST | OFF/ON | [Vehicle Condition]
|