DTC P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2714 | ECM detects malfunction on SLT (ON side) according to difference in revolutions of turbine (input) and output shaft (2 trip detection logic). |
|
| Related DTCs | P2714: Shift solenoid valve SLT/ON malfunction |
| Required sensors/Components | Shift solenoid valve SLT, Speed sensor (NT), Speed sensor (SPD) |
| Frequency of operation | Continuous |
| Duration | 1.0 second |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| Transmission shift position | D |
| Time after shifting N to D | 4.5 seconds or more |
| ATF (Automatic Transmission Fluid) temperature | -10°C (14°F) or more |
| Turbine Speed Sensor circuit | No circuit malfunction (P0717) |
| Vehicle Speed Sensor "A" circuit | No circuit malfunction (P0500) |
| Transmission Fluid Temperature Sensor "A" circuit | No circuit malfunction (P0712, P0713) |
| Shift Solenoid "A" (S1) circuit | No circuit malfunction (P0973, P0974) |
| Shift Solenoid "B" (S2) circuit | No circuit malfunction (P0976, P0977) |
| Torque Converter Clutch Pressure Control Solenoid (SLU) circuit | No circuit malfunction (P2759) |
| Pressure Control Solenoid "D" (SLT) circuit | No circuit malfunction (P2716) |
| Electronic Throttle Control System | No circuit malfunction (P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P0607, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135) |
| ECM gearshift command | 1st |
| Input (turbine) speed | 200 rpm or more |
| Output speed | 300 rpm or more |
| ECM gearshift command | 2nd |
| Input (turbine) speed | 200 rpm or more |
| Output speed | 300 rpm or more |
| ECM gearshift command | 3rd |
| Input (turbine) speed | 200 rpm or more |
| Output speed | 300 rpm or more |
| ECM gearshift command | 4th |
| Input (turbine) speed | 200 rpm or more |
| Output speed | 300 rpm or more |
| NT - NO x 1st gear ratio NT: Input (turbine) speed NO: Internal counter shaft speed | More than 300 rpm at output speed of 1000 rpm (Conditions vary with output speed) |
| Duration | 0.85 seconds or more |
| NT - NO x 2nd gear ratio | More than 300 rpm at output speed of 1000 rpm (Conditions vary with output speed) |
| Duration | 0.85 seconds or more |
| NT - NO x 3rd gear ratio | More than 300 rpm at output speed of 1000 rpm (Conditions vary with output speed) |
| Duration | 0.85 seconds or more |
| NT - NO x 4th gear ratio | More than 300 rpm at output speed of 1000 rpm (Conditions vary with output speed) |
| Duration | 0.85 seconds or more |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | [Test Details] Operate shift solenoid SLT and raise the line pressure.
| ON/OFF | [Vehicle Condition]
|
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P2714 is output | A |
| P2714 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE SLT |
![]() |
Remove the shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
| *a | Component without harness connected (Shift Solenoid Valve SLT) |
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
|
| ||||
| OK | ||
| ||