DTC P0751 Shift Solenoid "A" Performance (Shift Solenoid Valve S1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0751 | S1 stuck OFF malfunction*1: ECM determines there is malfunction when both of following conditions are met (2 trip detection logic). (a) When ECM directs gearshift to switch to 1st gear, actual gear is shifted to 4th. (b) When ECM directs gearshift to switch to 4th gear, actual gear is shifted to 4th. |
|
| S1 stuck ON malfunction*2: ECM determines that there is malfunction when both of following conditions are met (2 trip detection logic). (a) When ECM directs gearshift to switch from 3rd to 4th gear, actual gear is not shifted as above. (b) When ECM directs gearshift to switch to 4th gear, engine speed surges 1100 rpm or more. |
|
| Gearshift controlled by ECM | 1st | 2nd | 3rd | 4th |
| *1: Actual gear position under S1 stuck OFF malfunction | 4th | 3rd | 3rd | 4th |
| *2: Actual gear position under S1 stuck ON malfunction | 1st | 2nd | 2nd | 1st |
| Related DTCs | P0751: Shift solenoid valve S1/OFF malfunction Shift solenoid valve S1/ON malfunction |
| Required sensors/Components | Shift solenoid valve S1, Speed sensor (NT), Speed sensor (SPD) |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (a): 0.85 seconds OFF malfunction (b): 0.8 seconds ON malfunction (a): 0.8 seconds ON malfunction (b): 0.8 seconds |
| MIL operation | 2 driving cycle |
| Sequence of operation | None |
| ECT (Engine Coolant Temperature) | 60°C (140°F) or more |
| Time after shifting N to D | 4.5 seconds or more |
| Transmission shift position | D |
| Shift Solenoid "A" (S1) circuit | No circuit malfunction (P0973, P0974) |
| Shift Solenoid "B" (S2) circuit | No circuit malfunction (P0976, P0977) |
| ECT sensor circuit | No circuit malfunction (P0115, P0117, P0118) |
| Turbine Speed Sensor circuit | No circuit malfunction (P0717) |
| Vehicle Speed Sensor "A" circuit | No circuit malfunction (P0500) |
| Electronic Throttle Control System | No circuit malfunction (P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P0607, P060A, P060B P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135) |
| ECM gearshift command | 1st |
| Vehicle speed | 9 to 40 km/h (5.6 to 24.9 mph) |
| Throttle valve opening angle | 9% or more 7% or more at engine speed of 1900 rpm (Conditions vary with engine speed) |
| ECM gearshift command | 4th |
| Last ECM selected gear | 3rd |
| ECM gearshift command | 4th |
| Last ECM selected gear | 3rd |
| ECM gearshift command | 4th |
| V current - V last V current: Vehicle speed at current ECM selected gear V last: Vehicle speed at last ECM selected gear | Less than 15 km/h (9.3 mph) |
| TH current - TH last TH current: Throttle valve opening angle at current ECM selected gear TH last: Throttle valve opening angle at last ECM selected gear | Less than 30% |
| Vehicle speed (current) | Less than 85 km/h (52.8 mph) |
| Throttle valve opening angle (current) | Less than 45% |
| Engine speed (current) | 3200 rpm or more |
| Input speed/Output speed (NT/NO) NT: Input (turbine) speed NO: Internal counter shaft speed | 0.64 to 0.78 |
| Input speed/Output speed (NT/NO) | Changes as follows 0.95 to 1.09 (Last) to 0.64 to 0.78 (Current) |
| Input speed/Output speed (NT/NO) | Does not change as follows 0.95 to 1.09 (Last) to 0.64 to 0.78 (Current) |
NE change
| 1100 rpm or more |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | [Test Details] Operate shift solenoid valve and set each shift position. [Others]
| 1st/2nd/3rd/4th | Possible to check operation of shift solenoid valves. [Vehicle Condition] Vehicle speed: Less than 50 km/h (30 mph) |
| Gearshift controlled by ECM | 1st | 2nd | 3rd | 4th |
| Shift solenoid valve S1 | ON | ON | OFF | OFF |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0751) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0751 is output | A |
| P0751 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE S1 |
![]() |
Remove the shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - Solenoid Body | 20°C (68°F) | 11 to 15 Ω |
Connect the positive (+) lead to the terminal of the solenoid connector and the negative (-) lead to the solenoid body to check the solenoid valve operation.
| *a | Component without harness connected (Shift Solenoid Valve S1) |
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||