Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Hatchback)

POWER WINDOW CONTROL SYSTEM (for Hatchback) > Driver Side Power Window does not Operate with Power Window Master Switch


DESCRIPTION

If the driver side manual UP / DOWN and AUTO DOWN function does not operate, a malfunction may exist in the power window regulator motor assembly LH (driver side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B264212E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER SIDE)
  1. Inspect the power window regulator motor assembly LH (Click here).



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER SIDE) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - P/W RELAY AND BODY GROUND)


    B290897E01
  1. Disconnect the G20 power window regulator master switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    w/ Rear Power Window 
    Tester Connection
    Switch Condition
    Specified Condition
    G20-6 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    w/o Rear Power Window 
    Tester Connection
    Switch Condition
    Specified Condition
    G20-15 (B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Rear Power Window 
    Tester Connection
    Condition
    Specified Condition
    G20-1 (GND) - Body ground
    Always
    Below 1 Ω
    w/o Rear Power Window 
    Tester Connection
    Condition
    Specified Condition
    G20-7 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    w/ Rear Power Window
    *B
    w/o Rear Power Window
    *a
    Front view of wire harness connector
    (to Power Window Regulator Master Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
  1. Disconnect the G20 power window regulator master switch assembly connector.

  1. Disconnect the G21 power window regulator motor assembly LH (driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Rear Power Window 
    Tester Connection
    Condition
    Specified Condition
    G20-3 (U) - G21-2 (U)
    Always
    Below 1 Ω
    G20-4 (D) - G21-1 (D)
    Always
    Below 1 Ω
    G20-3 (U) - Body ground
    Always
    10 kΩ or higher
    G20-4 (D) - Body ground
    Always
    10 kΩ or higher
    w/o Rear Power Window 
    Tester Connection
    Condition
    Specified Condition
    G20-10 (U) - G21-2 (U)
    Always
    Below 1 Ω
    G20-12 (D) - G21-1 (D)
    Always
    Below 1 Ω
    G20-10 (U) - Body ground
    Always
    10 kΩ or higher
    G20-12 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)