ANTI-LOCK BRAKE SYSTEM (for Sedan) > TEST MODE PROCEDURE |
| TEST MODE PROCEDURE (SIGNAL CHECK) (Using Techstream) |
Procedure to enter Test Mode.
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Signal Check.
Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.
| Trouble Area | See procedure |
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| TS and CG terminal circuit |
Click here
|
| SPEED SENSOR CHECK (Using Techstream) |
Check the speed sensor signal.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| END OF SENSOR CHECK (Using Techstream) |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.
| READ DTC OF SIGNAL CHECK FUNCTION (Using Techstream) |
Read the DTC(s) by following the tester screen.
| TEST MODE PROCEDURE (SIGNAL CHECK) (Using SST Check Wire) |
Procedure to enter Test Mode.
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Turn the ignition switch to ON.
Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.
| Trouble Area | See procedure |
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| TS and CG terminal circuit |
Click here
|
| SPEED SENSOR CHECK (Using SST Check Wire) |
Check the speed sensor signal.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| END OF SENSOR CHECK (for Using SST Check Wire) |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.
| READ DTC OF SIGNAL CHECK FUNCTION (for Using SST Check Wire) |
![]() |
Using SST, connect terminals 13 (TC), 12 (TS) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Count the number of blinks of the ABS warning light.
After performing the check, disconnect SST from terminals 13 (TC), 12 (TS) and 4 (CG) of the DLC3 and turn the ignition switch off.
Turn the ignition switch to ON.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION (Procedure "A") |
| DTC Code | Detection Item | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH | Front axle hub bearing RH (speed sensor rotor) |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | Front axle hub bearing LH (speed sensor rotor) |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | Rear axle hub and bearing assembly RH (speed sensor rotor) |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | Rear axle hub and bearing assembly LH (speed sensor rotor) |