Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Hatchback)

SFI SYSTEM (for Hatchback) > Fuel Injector Circuit


DESCRIPTION

The fuel injector assemblies are located on the intake port. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A257630E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    A200903E27
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C43-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C44-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C45-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C46-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)



NG
Go to step 4
OK


2.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the fuel injector assembly injection and volume (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the fuel injector assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C43-2 - C51-20 (#10)
    Always
    Below 1 Ω
    C44-2 - C51-17 (#20)
    Always
    Below 1 Ω
    C45-2 - C51-18 (#30)
    Always
    Below 1 Ω
    C46-2 - C51-19 (#40)
    Always
    Below 1 Ω
    C43-2 or C51-20 (#10) - Body ground
    Always
    10 kΩ or higher
    C44-2 or C51-17 (#20) - Body ground
    Always
    10 kΩ or higher
    C45-2 or C51-18 (#30) - Body ground
    Always
    10 kΩ or higher
    C46-2 or C51-19 (#40) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)
  1. Disconnect the fuel injector assembly connectors.

  1. Remove the No. 1 integration relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C43-1 - 1E-2
    Always
    Below 1 Ω
    C44-1 - 1E-2
    Always
    Below 1 Ω
    C45-1 - 1E-2
    Always
    Below 1 Ω
    C46-1 - 1E-2
    Always
    Below 1 Ω
    C43-1 or 1E-2 - Body ground
    Always
    10 kΩ or higher
    C44-1 or 1E-2 - Body ground
    Always
    10 kΩ or higher
    C45-1 or 1E-2 - Body ground
    Always
    10 kΩ or higher
    C46-1 or 1E-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)