Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Hatchback)

SFI SYSTEM (for Hatchback) > ECM Power Source Circuit


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the EFI MAIN relay coil, closing the EFI MAIN relay contacts and supplying power to terminal +B and +B2 of the ECM.

WIRING DIAGRAM


A254094E08


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.INSPECT NO. 1 INTEGRATION RELAY (POWER SOURCE VOLTAGE)
A201293E06
  1. Remove the No. 1 integration relay.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)
OK


2.INSPECT NO. 1 INTEGRATION RELAY (EFI RELAY AND IG2 RELAY)
A257632E01
  1. Remove the No. 1 integration relay.

  1. Inspect the relay

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1E-4
      Battery voltage not applied to terminals 1D-7 and 1E-10
      10 kΩ or higher
      Battery voltage applied to terminals 1D-7 and 1E-10
      Below 1 Ω
      1C-1 - 1D-9
      Battery voltage not applied to terminals 1D-17 and 1E-10
      10 kΩ or higher
      Battery voltage applied to terminals 1D-17 and 1E-10
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (No. 1 Integration Relay)



NG
REPLACE NO. 1 INTEGRATION RELAY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Remove the No. 1 integration relay.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A72-46 (MREL) - 1D-7
    Always
    Below 1 Ω
    A72-2 (+B) - 1E-4
    Always
    Below 1 Ω
    A72-3 (+B2) - 1E-4
    Always
    Below 1 Ω
    A72-46 (MREL) or 1D-7 - Body ground
    Always
    10 kΩ or higher
    A72-2 (+B) or 1E-4 - Body ground
    Always
    10 kΩ or higher
    A72-3 (+B2) or 1E-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C51-16 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT ECM (IGSW TERMINAL VOLTAGE)
A246764E09
  1. Disconnect the ECM connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-37 (IGSW) - C51-16 (E1)
    Ignition switch ON
    11 to 14 V

Result 
Result
Proceed to
Outside standard range
A
Within standard range
B
Text in Illustration 
*a
Front view of wire harness connector
(to ECM)


B
REPLACE ECM (Click here)
A


6.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A72-37 (IGSW) - 1D-9
    Always
    Below 1 Ω
    A72-37 (IGSW) or 1D-9 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - IGNITION OR STARTER SWITCH ASSEMBLY - BODY GROUND)
  1. Remove the No. 1 integration relay.

  1. Disconnect the ignition or starter switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1D-17 - D109-6 (IG2)
    Always
    Below 1 Ω
    1E-10 - Body ground
    Always
    Below 1 Ω
    1D-17 or D109-6 (IG2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the ignition or starter switch assembly (Click here).



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)