DTC B1771 Passenger Side Buckle Switch Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1771 | One of following conditions is met:
|
|

| 1.CHECK FOR DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt assembly RH.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH.
Check that the connectors (on the occupant classification ECU side and front seat inner belt assembly RH side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH |

| *1 | Front Seat Inner Belt Assembly RH | *2 | Occupant Classification ECU |
| *3 | Front Seat Wire RH | *4 | Service Wire |
| *a | Front view of wire harness connector (to Occupant Classification ECU) | *b | Front view of wire harness connector (to Front Seat Inner Belt Assembly RH) |
| *c | Connector B | *d | Connector C |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| X4-5 - Body ground | Ignition switch ON | Below 1 V |
| X4-8 - Body ground |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (RBE+) and 2 (RBE-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| X4-8 - X4-5 | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| X4-5 - Body ground | Always | 1 MΩ or higher |
| X4-8 - Body ground | ||
| X4-8 - X4-5 |
|
| ||||
| OK | |
| 5.CHECK FOR DTC |
Connect the connectors to the occupant classification ECU and the front seat inner belt assembly RH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (PASSENGER SIDE BUCKLE SWITCH) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the front seat inner belt assembly RH (Click here).
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| NEXT | |
| 7.CHECK FOR DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 8.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| NEXT | |
| 9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
| NEXT | ||
| ||