Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Sedan)

POWER WINDOW CONTROL SYSTEM (for Sedan) > Rear Power Window RH does not Operate with Rear Power Window Switch RH


DESCRIPTION

If the rear RH side manual UP/DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B209175E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (POWER SOURCE)


    B204349E02
  1. Disconnect the H1 power window regulator switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H1-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the power window regulator switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B209438E01
  1. Remove the power window regulator switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    3 - 4
    UP
    Below 1 Ω
    1 - 2
    4 - 5
    OFF
    Below 1 Ω
    1 - 3
    4 - 5
    DOWN
    Below 1 Ω

  1. Reinstall the power window regulator switch assembly.



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR)


    B204350E02
  1. Disconnect the H1 power window regulator switch assembly connector.

  1. Disconnect the H2 power window regulator motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H1-4 (U) - H2-1 (U)
    Always
    Below 1 Ω
    H1-4 (U) or H2-1 (U) - Body ground
    Always
    10 kΩ or higher
    H1-1 (D) - H2-2 (D)
    Always
    Below 1 Ω
    H1-1 (D) or H2-2 (D) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the power window regulator switch assembly connector.

  1. Reconnect the power window regulator motor assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B086401E01
  1. Remove the power window regulator motor assembly.

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise

  1. Reinstall the power window regulator motor assembly .



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (REGULATOR MASTER SWITCH - REGULATOR SWITCH)


    B205374E02
  1. Disconnect the G1 power window regulator master switch assembly connector.

  1. Disconnect the H1 power window regulator switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G1-10 (U) - H1-5 (SU)
    Always
    Below 1 Ω
    G1-10 (U) or H1-5 (SU) - Body ground
    Always
    10 kΩ or higher
    G1-18 (D) - H1-2 (SD)
    Always
    Below 1 Ω
    G1-18 (D) or H1-2 (SD) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the power window regulator master switch assembly connector.

  1. Reconnect the power window regulator switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (REAR RH SWITCH)
  1. Remove the power window regulator master switch assembly.



    B209378E04
  1. Measure the resistance according to the value(s) in the table below.

    1. Remove the power window regulator master switch assembly.

    2. Measure the resistance of the switch when the switch is operated.

      Standard resistance:
      Tester Connection
      Window Lock Switch Condition
      Power Window Switch Condition
      Specified Condition
      1 (E) - 18 (D)
      6 (B) - 10 (U)
      OFF
      UP
      Below 1 Ω
      1 (E) - 10 (U)
      1 (E) - 18 (D)
      OFF
      OFF
      Below 1 Ω
      1 (E) - 10 (U)
      6 (B) - 18 (D)
      OFF
      DOWN
      Below 1 Ω
      1 (E) - 18 (D)
      ON
      UP
      10 kΩ or higher
      6 (B) - 10 (U)
      Below 1 Ω
      10 (U) - 18 (D)
      ON
      OFF
      Below 1 Ω
      1 (E) - 10 (U)
      ON
      DOWN
      10 kΩ or higher
      6 (B) - 18 (D)
      Below 1 Ω

    3. Reinstall the power window regulator master switch assembly.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL (Click here)