Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Hatchback)

POWER WINDOW CONTROL SYSTEM (for Hatchback) > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch


DESCRIPTION

If the front passenger side manual UP / DOWN function does not operate, a malfunction may exist in the power window regulator motor assembly RH (front passenger side), power window regulator switch assembly (front passenger side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B290898E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE)
  1. Inspect the power window regulator switch assembly (front passenger side) (Click here).



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE) (Click here)
OK


2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER SIDE)
  1. Inspect the power window regulator motor assembly RH (front passenger side) (Click here).



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER SIDE) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - P/W RELAY)


    B290899E01
  1. Disconnect the F20 power window regulator switch assembly (front passenger side) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F20-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Window Regulator Switch Assembly (Front Passenger Side))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
  1. Disconnect the F20 power window regulator switch assembly (front passenger side) connector.

  1. Disconnect the F21 power window regulator motor assembly RH (front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F20-4 (U) - F21-2 (U)
    Always
    Below 1 Ω
    F20-1 (D) - F21-1 (D)
    Always
    Below 1 Ω
    F20-4 (U) - Body ground
    Always
    10 kΩ or higher
    F20-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
  1. Disconnect the F20 power window regulator switch assembly (front passenger side) connector.

  1. Disconnect the G20 power window regulator master switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Rear Power Window 
    Tester Connection
    Condition
    Specified Condition
    F20-5 (SU) - G20-16 (U)
    Always
    Below 1 Ω
    F20-2 (SD) - G20-15 (D)
    Always
    Below 1 Ω
    F20-5 (SU) - Body ground
    Always
    10 kΩ or higher
    F20-2 (SD) - Body ground
    Always
    10 kΩ or higher
    w/o Rear Power Window 
    Tester Connection
    Condition
    Specified Condition
    F20-5 (SU) - G20-16 (U)
    Always
    Below 1 Ω
    F20-2 (SD) - G20-18 (D)
    Always
    Below 1 Ω
    F20-5 (SU) - Body ground
    Always
    10 kΩ or higher
    F20-2 (SD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)