Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for Hatchback)

LIGHTING SYSTEM (for Hatchback) > Headlight Dimmer Switch Circuit


DESCRIPTION

The main body ECU receives the following switch information:
  1. Light control switch in OFF, DRL*1, TAIL or HEAD position
  2. Dimmer switch in HIGH, LOW or FLASH (pass) position
  3. Fog light switch in FRONT or OFF position*2
    1. *1: w/ DRL OFF function
    2. *2: w/ Fog Light
The combination meter assembly receives the following signals:
  1. Turn signal switch turn right or turn left signal

WIRING DIAGRAM


E275981E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus:

    1. for Main Body ECU: Body Electrical / Main Body / Data List.

    2. for Combination Meter: Body Electrical / Combination Meter / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer SW
    Dimmer switch high signal /
    OFF or ON
    OFF: Dimmer switch in low position
    ON: Dimmer switch in high or high flash position
    -
    Passing Light SW
    Dimmer switch high flash signal /
    OFF or ON
    OFF: Dimmer switch not in high flash position
    ON: Dimmer switch in high flash position
    -
    Front Fog Light SW*1
    Fog light switch signal /
    OFF or ON
    OFF: Fog light switch off
    ON: Fog light switch on
    -
    Auto Light SW*2
    Light control switch DRL signal /
    OFF or ON
    OFF: Light control switch not in DRL position
    ON: Light control switch in DRL position
    -
    Head Light SW (Head)
    Light control switch HEAD signal /
    OFF or ON
    OFF: Light control switch not in HEAD position
    ON: Light control switch in HEAD position
    -
    Head Light SW (Tail)
    Light control switch TAIL signal /
    OFF or ON
    OFF: Light control switch not in TAIL and HEAD position
    ON: Light control switch in TAIL or HEAD position
    -

    1. *1: w/ Fog Light
    2. *2: w/ DRL OFF function

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Turn Signal Switch (Right)
    Turn signal switch signal (turn right) /
    OFF or ON
    OFF: Turn signal switch right off (turn right)
    ON: Turn signal switch right on (turn right)
    -
    Turn Signal Switch (Left)
    Turn signal switch signal (turn left) /
    OFF or ON
    OFF: Turn signal switch left off (turn left)
    ON: Turn signal switch left on (turn left)
    -

    OK:
    Normal conditions listed above are displayed.

    Result 
    Result
    Proceed to
    OK
    A
    NG (Light control switch, dimmer switch or fog light switch*1)
    B
    NG (Turn signal switch)
    C
    1. *1: w/ Fog Light



B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (LIGHT CONTROL SWITCH, DIMMER SWITCH OR FOG LIGHT SWITCH)
  1. Inspect the headlight dimmer switch assembly (Click here).



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the D106 headlight dimmer switch assembly connector.

  1. Disconnect the D143 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D106-4 (BFG) - D143-27 (FFOG)*1
    Always
    Below 1 Ω
    D106-11 (HU) - D143-5 (HU)
    Always
    Below 1 Ω
    D106-17 (HF) - D143-8 (HF)
    Always
    Below 1 Ω
    D106-18 (T) - D143-30 (TAIL)
    Always
    Below 1 Ω
    D106-19 (A) - D143-28 (A)*2
    Always
    Below 1 Ω
    D106-20 (H) - D143-29 (HEAD)
    Always
    Below 1 Ω
    D106-3 (LFG) - Body ground
    Always
    Below 1 Ω
    D106-12 (EL) - Body ground
    Always
    Below 1 Ω
    D106-4 (BFG) or D143-27 (FFOG) - Body ground*1
    Always
    10 kΩ or higher
    D106-11 (HU) or D143-5 (HU) - Body ground
    Always
    10 kΩ or higher
    D106-17 (HF) or D143-8 (HF) - Body ground
    Always
    10 kΩ or higher
    D106-18 (T) or D143-30 (TAIL) - Body ground
    Always
    10 kΩ or higher
    D106-19 (A) or D143-28 (A) - Body ground*2
    Always
    10 kΩ or higher
    D106-20 (H) or D143-29 (HEAD) - Body ground
    Always
    10 kΩ or higher

    1. *1: w/ Fog Light
    2. *2: w/ DRL OFF function



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (Click here)  

4.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (TURN SIGNAL SWITCH)
  1. Inspect the headlight dimmer switch assembly (Click here).



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
  1. Disconnect the D106 headlight dimmer switch assembly connector.

  1. Disconnect the D101 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D106-13 (TR) - D101-9 (ER)
    Always
    Below 1 Ω
    D106-15 (TL) - D101-10 (EL)
    Always
    Below 1 Ω
    D106-12 (EL) - Body ground
    Always
    Below 1 Ω
    D106-13 (TR) or D101-9 (ER) - Body ground
    Always
    10 kΩ or higher
    D106-15 (TL) or D101-10 (EL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)