Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM (for Sedan)

POWER DOOR LOCK CONTROL SYSTEM (for Sedan) > All Doors cannot be Locked / Unlocked Simultaneously


DESCRIPTION

The main body ECU receives switch signals from the door control switch and driver side door key cylinder, and activates the door lock motor on each door accordingly.

WIRING DIAGRAM


B283862E01


INSPECTION PROCEDURE

1.INSPECT FRONT DOOR LOCK ASSEMBLY LH
B079551E05
  1. Apply the battery voltage to the door lock motor and measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    8 (LSSR) - 7 (E)
    Battery positive (+) → Terminal 1
    Battery negative(-) → Terminal 4
    Below 1 Ω
    8 (LSSR) - 7 (E)
    Battery positive (+) → Terminal 4
    Battery negative(-) → Terminal 1
    10 kΩ or higher



NG
REPLACE FRONT DOOR LOCK ASSEMBLY LH (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK ASSEMBLY LH)
B145640E01
  1. Disconnect the D33main body ECU connector.

  1. Disconnect the G5 door lock connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D33-21 (LSWD) - G5-8 (LSSR)
    Below 1 Ω
    D33-21 (LSWD) or G5-8 (LSSR) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK DOOR LOCK OPERATION
  1. Proceed to the next step according to the symptom listed in the table below.

    Result:

    Symptom
    Proceed to
    Doors cannot be locked using door control switch (for front driver door side)
    A
    Doors cannot be locked using driver side door key cylinder
    B
    Doors cannot be locked using front passenger side door key cylinder
    C
    Doors cannot be locked using door control switch (for passenger side)
    D



B
Go to step 6

C
Go to step 8

D
Go to step 10
A


4.INSPECT DOOR CONTROL SWITCH (for Front Driver Door Side)
B288516E01
B145638E01
  1. w/ Power window:

    1. Disconnect the G1 door control switch (for front driver door side) connector.

    2. Measure the resistance of the switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (L) - 1 (E)
      Lock
      Below 1 Ω
      9 (UL) - 1 (E)
      Unlock
      Below 1 Ω
      2 (L) - 1 (E)
      OFF
      10 kΩ or higher
      9 (UL) - 1 (E)
      OFF
      10 kΩ or higher

    3. Reconnect the door control switch (for front driver door side) connector.

  1. w/o Power window:

    1. Disconnect the G7 door control switch (for front driver door side) connector.

    2. Measure the resistance of the switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (L) - 4 (E)
      Lock
      Below 1 Ω
      2 (UL) - 4 (E)
      Unlock
      Below 1 Ω
      3 (L) - 4 (E)
      OFF
      10 kΩ or higher
      2 (UL) - 4 (E)
      OFF
      10 kΩ or higher

    3. Reconnect the door control switch (for front driver door side) connector.



NG
REPLACE DOOR CONTROL SWITCH (for Front Driver Door Side) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH (Front Driver Door Side))
B123822E28
B145637E01
  1. w/ Power window:

    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the G1 door control switch (for front driver door side) connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4H-5(UL1) - G1-9(UL)
      Below 1 Ω
      4H-4(L1) - G1-2(L)
      Below 1 Ω
      4H-5(UL1) or G1-9(UL) - Body ground
      10 kΩ or higher
      4H-4(L1) or G1-2(L) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the door control switch (for front driver door side) connector.

  1. w/o Power window:

    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the G7 door control switch (for front driver door side) connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4H-5 (UL1) - G7-2 (UL)
      Below 1 Ω
      4H-4 (L1) - G7-3 (L)
      Below 1 Ω
      4H-5 (UL1) or G7-2 (UL) - Body ground
      10 kΩ or higher
      4H-4 (L1) or G7-3 (L) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the door control switch (for front driver door side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

6.READ VALUE USING TECHSTREAM
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on tester, read on the "Data List".


Main Body:

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Key SW-Lock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to lock position
OFF: Driver side door key cylinder is turned to unlock position
-


Main Body:

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Key SW-Unlock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to lock position
OFF: Driver side door key cylinder is turned to unlock position
-

OK:
ON (driver side door key cylinder is turned to lock/unlock position) appears on tester screen.



OK
REPLACE MAIN BODY ECU
NG


7.CHECK HARNESS AND CONNECTOR (DRIVER SIDE DOOR LOCK ASSEMBLY - MAIN BODY ECU)
B123825E01
  1. Disconnect the D33 and 4H main body ECU connectors.

  1. Disconnect the G5 door lock connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D33-14 (UL3) - G5-10 (UL)
    Below 1 Ω
    4H-7 (L2) - G5-9 (L)
    Below 1 Ω
    D33-14 (UL3) or G5-10 (UL) - Body ground
    10 kΩ or higher
    4H-7 (L2) or G5-9 (L) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connectors.

  1. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.READ VALUE USING TECHSTREAM
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on tester, read on the "Data List".


Main Body:

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Key SW-Lock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to lock position
OFF: Driver side door key cylinder is turned to unlock position
-


Main Body:

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Key SW-UL
Door key-linked unlock switch signal/ ON or OFF
ON: Door key cylinder is turned to unlock position
OFF: Door key cylinder is turned to lock position
-

OK:
ON (driver side door key cylinder is turned to lock/unlock position) appears on screen.



OK
REPLACE MAIN BODY ECU
NG


9.CHECK HARNESS AND CONNECTOR (PASSENGER SIDE DOOR LOCK ASSEMBLY - MAIN BODY ECU)
B123858E14
  1. Disconnect the 4H main body ECU connector.

  1. Disconnect the F5 front door lock assembly connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4H-15 (UL2) - F5-5 (UL)
    Below 1 Ω
    4H-16 (L2) - F5-6 (L)
    Below 1 Ω
    4H-15 (UL2) or F5-5 (UL) - Body ground
    10 kΩ or higher
    4H-16 (L2) or F5-6 (L) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the front door lock assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

10.INSPECT DOOR CONTROL SWITCH (for Front Passenger Door Side)
B145638E02
  1. Disconnect the F7 door control switch (for front passenger door side) connector.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (L) - 4 (E)
    Lock
    Below 1 Ω
    2 (UL) - 4 (E)
    Unlock
    Below 1 Ω
    3 (L) - 4 (E)
    OFF
    10 kΩ or higher
    2 (UL) - 4 (E)
    OFF
    10 kΩ or higher

  1. Reconnect the door control switch (for front passenger door side) connector.



NG
REPLACE DOOR CONTROL SWITCH (for Front Passenger Door Side) (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH (Passenger Door Side))
B278026E01
  1. Disconnect the 4C and 4E main body ECU connector.

  1. Disconnect the F7 door control switch (for front passenger door side) connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4C-10 (UL1) - F7-2 (UL)
    Below 1 Ω
    4E-11 (L1) - F7-3 (L)
    Below 1 Ω
    4C-10 (UL1) or F7-2 (UL) - Body ground
    10 kΩ or higher
    4E-11 (L1) or F7-3 (L) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the door control switch (for front passenger door side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU