Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (for Sedan)

ENGINE IMMOBILISER SYSTEM (for Sedan) > ECU Power Source Circuit


DESCRIPTION

This circuit provides power to operate the transponder key ECU assembly.

WIRING DIAGRAM


B119967E01


INSPECTION PROCEDURE

1.INSPECT FUSE (ECU-B)


    B122728E01
  1. Remove the ECU-B fuse from the engine room R/B and J/B.

  1. Measure the ECU-B fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ECU-B fuse.



NG
REPLACE FUSE
OK


2.INSPECT FUSE (IGN)


    A107935E06
  1. Remove the IGN fuse from the main body ECU.

  1. Measure the IGN fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the IGN fuse.



NG
REPLACE FUSE
OK


3.INSPECT INTEGRATION NO.1 RELAY (IG2 RELAY AND AM2 FUSE)


    A107921E11
  1. Remove the integration relay from the engine room R/B and J/B.

  1. Inspect the AM2 fuse.

    1. Remove the AM2 fuse from the integration relay.

    2. Measure the resistance of the AM2 fuse.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the AM2 fuse.

  1. Inspect the IG2 relay.

    1. Measure the resistance between the terminals shown below.

      Standard resistance:
      Tester Connections
      Specified Conditions
      1C-1-1B-4
      10 kΩ or higher
      Below 1 Ω (when battery voltage is applied to terminals 1B-2 and 1B-3)
      1C-1-1B-1
      Below 1 Ω

    2. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY (Click here)
OK


4.INSPECT IGNITION SWITCH ASSEMBLY


    A107906E01
  1. Disconnect the D8 ignition switch connector.

  1. Measure the resistance between the terminals shown below.

    Standard resistance:
    Key Position
    Tester Connection
    Specified Condition
    LOCK
    -
    10 kΩor higher
    ACC
    2-4
    Below 1 Ω
    ON
    1-2-4
    Below 1 Ω
    5-6
    Below 1 Ω
    START
    1-3-4
    Below 1 Ω
    5-6-7
    Below 1 Ω

  1. Reconnect the D8 ignition switch connector.



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)


    B110782E07
  1. Disconnect the D23 transponder key ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D23-1 (+B) - Body ground
    D23-1 (+B) - Body ground
    11 to 14 V
    D23-2 (IG) - Body ground
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    D23-16 (GND) - Body ground
    Below 1 Ω

  1. Reconnect the D23 transponder key ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)