OCCUPANT CLASSIFICATION SYSTEM (for Hatchback) > Trouble in Passenger Airbag ON/OFF Indicator |
| Front Passenger Seat Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
| ON Indicator | OFF Indicator | ||
| Vacant | OFF | OFF | OFF |
| Adult is seated | ON | OFF | OFF |
| Child is seated | OFF | ON | OFF |
| Child restraint system is set | OFF | ON | OFF |
| Occupant classification system failure | OFF | ON | ON |
| 1.CHECK SRS WARNING LIGHT |
Turn the ignition switch to ON, and check the SRS warning light condition.
| Result | Proceed to |
| OK | A |
| NG (w/ VSC) | B |
| NG (w/o VSC) | C |
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
|
| ||||
| OK | ||
| ||
| 3.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT |
Turn the ignition switch off.
Loosen the 4 installation bolts of the front seat assembly RH.
Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.
| NEXT | |
| 4.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH) |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, read the Data List (Click here).
Read the display when the passenger side buckle switch is operated.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Passenger Buckle SW | Buckle switch (Passenger side)/ NG/Unset/Set | NG: Passenger side seat belt is malfunctioning Unset: Front passenger side seat belt is unfastened Set: Front passenger side seat belt is fastened | - |
|
| ||||
| OK | |
| 6.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the occupant classification ECU and the 2 occupant classification sensors.
Check that the connectors (on the occupant classification ECU side and 2 occupant classification sensors side) are not damaged.
|
| ||||
| OK | |
| 7.REPLACE OCCUPANT CLASSIFICATION ECU |
Replace the occupant classification ECU (Click here).
| NEXT | |
| 8.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
| NEXT | ||
| ||
| 9.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the occupant classification ECU and front seat inner belt assembly RH.
Check that the connectors (on the occupant classification ECU side and front seat inner belt RH side) are not damaged.
|
| ||||
| OK | |
| 10.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (PASSENGER SIDE BUCKLE SWITCH) |
Replace the front seat inner belt assembly RH (Click here).
| NEXT | |
| 11.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
| NEXT | ||
| ||