Home › Drivetrain · U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM (for Hatchback)

DTC    P2716    Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)


DESCRIPTION

Refer to P2714 .

DTC No.
DTC Detection Condition
Trouble Area
P2716
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detecting logic).
  1. Wire harness or connector
  2. Transmission wire
  3. Shift solenoid valve SLT
  4. ECM

MONITOR DESCRIPTION

When an open or short in the linear solenoid valve (SLT) circuit is detected, the ECM interprets this as a fault. The ECM turns on the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P2716: Shift solenoid valve SLT/Range check
Required sensors/Components
Shift solenoid valve SLT
Frequency of operation
Continuous
Duration
1.0 second
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor runs whenever the following DTCs are not present
None
Solenoid current cut status
Not cut
Battery voltage
11 V or more
Target duty cycle
19% or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Solenoid voltage monitor from MIC
No signal

COMPONENT OPERATING RANGE


Solenoid voltage monitor from MIC
Signal input

WIRING DIAGRAM


C243327E06


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
C229166E23
  1. Disconnect the C68 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (SLT+) - 8 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    3 (SLT+) - Body ground
    Always
    10 kΩ or higher
    8 (SLT-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
C233488E11
  1. Connect the C68 transmission wire connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C51-73 (SLT+) - C51-72 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C51-73 (SLT+) - Body ground
    Always
    10 kΩ or higher
    C51-72 (SLT-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

3.INSPECT SHIFT SOLENOID VALVE SLT
C204845E06
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.

    Text in Illustration 
    *a
    Component without harness connected
    (Shift Solenoid Valve SLT)



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)