FRONT SHOCK ABSORBER (for Sedan) > INSTALLATION |
| 1. INSTALL STRUT MOUNTING BEARING |
![]() |
Using a brass bar and press, install the strut mounting bearing to the front upper coil spring seat.
| 2. INSTALL FRONT COIL SPRING |
![]() |
Secure SST in a vise.
![]() |
Attach the arm of SST to the diameter of the front coil spring.
| *a | Correct |
| *b | Incorrect |
Using SST, compress the front coil spring.
![]() |
Install the front coil spring to the front shock absorber assembly.
| *a | Lower End |
| 3. INSTALL FRONT UPPER COIL SPRING INSULATOR |
| 4. INSTALL FRONT SPRING BUMPER |
![]() |
Install the front spring bumper to the front upper coil spring seat with the air discharge groove of the front spring bumper and the rib portion of the upper coil spring seat aligned.
| *a | Rib Portion |
| *b | Air Discharge Groove |
| 5. INSTALL FRONT UPPER COIL SPRING SEAT |
Install the front upper coil spring seat with the strut mounting bearing and the front spring bumper to the front shock absorber.
| 6. INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT |
Temporarily tighten a new front support to front shock absorber nut.
Remove SST from the front coil spring.
![]() |
Using SST and a long socket hexagon wrench 6 mm, fix the front shock absorber rod and tighten the front support to front shock absorber nut.
| *1 | Long Socket Hexagon Wrench 6 mm |
| *a | Turn |
| *b | Hold |
| 7. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY |
| 8. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING |
![]() |
Temporarily tighten a new nut through the No. 2 suspension support.
Install the front shock absorber with coil spring to the steering knuckle.
Install the 2 bolts and 2 nuts.
| 9. INSTALL FRONT FLEXIBLE HOSE (w/ ABS) |
Install the front flexible hose and the front speed sensor with the bolt.
| 10. INSTALL FRONT FLEXIBLE HOSE (w/o ABS) |
Install the front flexible hose with the bolt.
| 11. INSTALL FRONT STABILIZER LINK ASSEMBLY |
Install the front stabilizer link assembly with the nut.
| 12. INSTALL FRONT WHEEL |
| 13. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING |
![]() |
Using SST and a long socket hexagon wrench 6 mm, fix the shock absorber rod and tighten the nut.
| *1 | Long Socket Hexagon Wrench 6 mm |
| *a | Turn |
| *b | Hold |
| 14. INSTALL FRONT SUSPENSION SUPPORT DUST COVER |
| 15. INSTALL OUTER COWL TOP PANEL |
Install the cowl top panel outer with the 8 bolts.
Install the cowl top to cowl inner brace with the 2 bolts.
Connect the wire harness clamp.
| 16. INSTALL FRONT AIR SHUTTER SEAL |
Engage the 3 claws to install the front air shutter seal RH.
| 17. INSTALL FRONT WIPER MOTOR AND LINK |
![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
| 18. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Connect the washer hoses.
Engage the 5 hooks.
![]() |
Engage the 8 hooks and the 4 claws.
Install the cowl top ventilator louver sub-assembly with the 3 clips.
| 19. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Engage the 3 claws and install the cowl side ventilator sub-assembly LH.
| 20. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 21. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 22. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 23. INSTALL FRONT WIPER ARM HEAD CAP |
![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 24. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |