Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER (for Hatchback)

FRONT SHOCK ABSORBER (for Hatchback) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side as for the LH side.
  2. The procedure listed below is for the LH side.



1. INSTALL STRUT MOUNTING BEARING


    C235444
  1. Using a brass bar and press, install the strut mounting bearing to the front coil spring upper seat.

    NOTICE:
    The strut mounting bearing must be securely installed.



2. INSTALL FRONT COIL SPRING


    C265549E01
  1. Secure SST in a vise.

    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)



    C275706E03
  1. Attach the arm of SST to the diameter of the front coil spring.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    CAUTION:
    1. Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
    2. Make sure that the claws of the hooks are securely attached.

  1. Using SST, compress the front coil spring.

    CAUTION:
    1. If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.
    2. Do not compress the spring until the coil springs contact each other.
    3. Do not use an impact wrench. It will damage SST.



    C235694E02
  1. Install the front coil spring to the front shock absorber assembly.
    Text in Illustration 
    *a
    Lower End

    NOTICE:
    A spring of a smaller diameter should be installed in the upward direction.

    HINT:
    Fit the lower end of the front coil spring into the gap of the front shock absorber lower seat.



3. INSTALL FRONT COIL SPRING UPPER INSULATOR


4. INSTALL FRONT SPRING BUMPER


    C107510E05
  1. Install the front spring bumper to the front coil spring upper seat with the air discharge groove of the front spring bumper and the rib portion of the front coil spring upper seat aligned.
    Text in Illustration 
    *a
    Rib Portion
    *b
    Air Discharge Groove

    NOTICE:
    Securely insert the front spring bumper into the front coil spring upper seat.



5. INSTALL FRONT COIL SPRING UPPER SEAT
  1. Install the front coil spring upper seat with the strut mounting bearing and the front spring bumper to the front shock absorber.

  1. Temporarily tighten a new nut.

  1. Remove SST from the front coil spring.

    NOTICE:
    Do not use an impact wrench. It will damage SST.



    C229624E06
  1. Using SST and a long socket hexagon wrench 6 mm, fix the front shock absorber rod and tighten the nut.
    Text in Illustration 
    *1
    Long Socket Hexagon Wrench 6 mm
    *a
    Turn
    *b
    Hold

    SST
    09729-97202  

    Torque:
    without SST:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }
    with SST:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    HINT:
    1. This torque value is effective when SST is parallel to the torque wrench.
    2. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a SST with a fulcrum length of 40 mm (1.57 in.).
    3. If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).



6. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


7. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    C235028
  1. Temporarily tighten a new nut through the front No. 2 suspension support.

  1. Install the front shock absorber with coil spring to the steering knuckle.

  1. Install the 2 bolts and 2 nuts.

    Torque:
    164 N*m{ 1672 kgf*cm , 121 ft.*lbf }

    HINT:
    Keep the bolt from rotating while installing and tightening the nuts.



8. INSTALL FRONT FLEXIBLE HOSE (w/ ABS)
  1. Install the front flexible hose and the front speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the front flexible hose and the front speed sensor without twisting them.



9. INSTALL FRONT FLEXIBLE HOSE (w/o ABS)
Install the front flexible hose with the bolt.

Torque:
29 N*m{ 300 kgf*cm , 22 ft.*lbf }

NOTICE:
Install the front flexible hose without twisting it.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY
  1. Install the front stabilizer link assembly with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    Using a socket hexagon wrench 6 mm to hold the stud.



11. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



12. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    C234273E02
  1. Using SST and a long socket hexagon wrench 6 mm, fix the front shock absorber rod and tighten the nut.
    Text in Illustration 
    *1
    Long Socket Hexagon Wrench 6 mm
    *a
    Hold
    *b
    Turn

    SST
    09729-97202  

    Torque:
    with SST:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    without SST:
    49 N*m{ 495 kgf*cm , 36 ft.*lbf }



13. INSTALL FRONT SUSPENSION SUPPORT DUST COVER


14. INSTALL OUTER COWL TOP PANEL
  1. Install the outer cowl top panel with the 8 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and install the wire harness.



15. INSTALL INNER COWL TOP TO COWL BRACE
  1. Install the cowl top to cowl brace with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



16. INSTALL FRONT NO. 1 VENTILATOR SEAL
  1. Engage the clip and install the front No. 1 ventilator seal.



17. INSTALL FRONT AIR SHUTTER SEAL RH

HINT:
Use the same procedure for the RH and LH sides.



18. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
(Click here)


19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)