FRONT STABILIZER BAR (for Sedan) > INSTALLATION |
| 1. INSTALL FRONT STABILIZER BAR BUSH |
![]() |
Install the stabilizer bar bush to the stabilizer bar.
| 2. INSTALL FRONT STABILIZER BAR |
![]() |
Install the stabilizer onto the crossmember with the paint mark on the left side of the vehicle.
| 3. INSTALL FRONT STABILIZER BRACKET LH |
![]() |
Provisionally tighten bolt A.
Tighten the bolts to the specified torque, in the order of B then A.
| 4. INSTALL FRONT STABILIZER BRACKET RH |
| 5. INSTALL POWER STEERING GEAR |
Install the steering gear assembly onto the front suspension crossmember with the 2 bolts and 2 nuts.
| 6. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
![]() |
Place wooden blocks or plate lift attachments on an engine lifter, and then set the front suspension crossmember sub-assembly so that the attachments are in the positions shown in the illustration.
![]() | Front of the Vehicle |
![]() | Attachment Placement Positions |
Temporarily install the front suspension crossmember sub-assembly to the body with the 6 bolts.
By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

| *a | Datum Hole | *b | OK |
| *c | NG | - | - |
![]() | Front of the Vehicle | - | - |
Install the engine moving control rod with the bolt.
| 7. INSTALL FRONT LOWER SUSPENSION ARM LH |
Install the front lower suspension arm sub-assembly LH to the steering knuckle with a new castle nut.
Install a new clip.
| 8. INSTALL FRONT LOWER SUSPENSION ARM RH |
| 9. INSTALL TIE ROD END SUB-ASSEMBLY LH |
Install the tie rod end sub-assembly LH to the steering knuckle with a new castle nut.
Install a new cotter pin.
| 10. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 11. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
Install the front stabilizer link assembly LH with the nut.
| 12. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 13. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Install clip B to the body portion and install the No. 1 steering column hole cover sub-assembly to the body portion with clip A.
| 14. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Align the matchmarks and install the steering sliding yoke sub-assembly to the power steering gear.
| *1 | Steering Sliding Yoke Sub-assembly |
| *a | Matchmark |
Install bolt B.
Tighten bolt A.
| 15. INSTALL COLUMN HOLE COVER SILENCER SHEET |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 16. INSTALL FRONT WHEEL |
| 17. POSITION WHEELS FACING STRAIGHT AHEAD |
| 18. INSTALL OUTER COWL TOP PANEL |
Install the cowl top panel outer with the 8 bolts.
Install the cowl top to cowl inner brace with the 2 bolts.
Connect the wire harness clamp.
| 19. INSTALL FRONT AIR SHUTTER SEAL |
Engage the 3 claws to install the front air shutter seal RH.
| 20. INSTALL FRONT WIPER MOTOR AND LINK |
![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
| 21. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Connect the washer hoses.
Engage the 5 hooks.
![]() |
Engage the 8 hooks and the 4 claws.
Install the cowl top ventilator louver sub-assembly with the 3 clips.
| 22. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Engage the 3 claws and install the cowl side ventilator sub-assembly LH.
| 23. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 24. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 25. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 26. INSTALL FRONT WIPER ARM HEAD CAP |
![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 27. INSPECT HOOD |
Check that the clearance measurements are within the standard ranges.

| Area | Measurement | Area | Measurement |
| A | 2.35 to 6.35 mm (0.092 to 0.250 in.) | C | 2.0 to 5.0 mm (0.079 to 0.197 in.) |
| B | -2 to 2 mm (-0.079 to 0.079 in.) | - | - |
| 28. ADJUST HOOD |
![]() |
Loosen the hood side hinge bolts.
Move the hood to adjust the clearance to within the standard range.
Tighten the hood side hinge bolts after the adjustment.
![]() |
Adjust the height of the hood front end by turning the cushion rubber.
![]() |
Adjust the hood lock.
Loosen the 3 bolts.
Adjust the hood lock position so that the striker can enter it smoothly.
Tighten the 3 bolts after the adjustment.
| 29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 30. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |