DTC B1615/14 Front Airbag Sensor LH Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1615/14 |
|
|

| 1.CHECK DTC |
![]() |
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.
|
| ||||
| OK | |
| 3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH.
Using a service wire, connect A12-1 and A12-2 of connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| D16-30 (+SL) - D16-28 (-SL) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| D16-30 (+SL) - D16-28 (-SL) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on.
Measure the voltage.
| Tester Connection | Switch Condition | Specified Condition |
| D16-30 (+SL) - Body ground | Ignition switch on | Below 1 V |
| D16-28 (-SL) - Body ground | Ignition switch on | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| D16-30 (+SL) - Body ground | Always | 1 MΩ or higher |
| D16-28 (-SL) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK FRONT AIRBAG SENSOR LH |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the front airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1615/14 is output. | A |
| DTC B1610/13 is output. | B |
| DTC B1610/13 and B1615/14 are not output. | C |
|
| ||||
|
| ||||
| C | ||
| ||
| 8.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| AD1-3 (+SL) - AD1-4 (-SL) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 9.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| AD1-3 (+SL) - AD1-4 (-SL) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 10.CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() |
Turn the ignition switch to the lock position.
Disconnect the negative(-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on.
Measure the voltage.
| Tester Connection | Switch Condition | Specified Condition |
| AD1-3 (+SL) - Body ground | Ignition switch on | Below 1 V |
| AD1-4 (-SL) - Body ground | Ignition switch on | Below 1 V |
|
| ||||
| OK | ||
| ||
| 11.CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| AD1-3 (+SL) - Body ground | Always | 1 MΩ or higher |
| AD1-4 (-SL) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||