Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for Sedan)

BRAKE PEDAL (for Sedan) > INSTALLATION



1. INSTALL BRAKE PEDAL PAD
  1. Install the brake pedal pad onto the brake pedal.



2. INSTALL BRAKE PEDAL BUSH
  1. Apply lithium soap base glycol grease to the 2 bushes.

  1. Install the 2 bushes onto the brake pedal.



3. INSTALL BRAKE PEDAL
  1. Install the brake pedal onto the pedal support with the brake pedal shaft and nut.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



4. INSTALL BRAKE PEDAL SUPPORT


C116881
  1. Install the pedal support with the bolt and 4 nuts.

    Torque:
    Bolt:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



5. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the push rod pin.



    C116880
  1. Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.



6. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER


C116879
  1. Install a new stop light switch mounting adjuster onto the pedal support.



7. INSTALL STOP LIGHT SWITCH


F049043E01
  1. Insert the stop light switch into the adjuster until it just touches the brake pedal.

    NOTICE:
    Do not depress the brake pedal.



    F049044E08
  1. Make a quarter turn clockwise to install the stop light switch.

    NOTICE:
    Do not depress the brake pedal.

    HINT:
    The turning torque for installing the stop light switch:

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

  1. Check the stop light switch clearance.

    Stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

  1. Connect the wire harness clamp onto the pedal support.

  1. Connect the connector to the stop light switch.



8. INSPECT AND ADJUST BRAKE PEDAL


C116874E01
  1. Inspect the brake pedal height.

    Pedal height from floor panel:
    w/ ABS
    w/o ABS
    113.1 to 123.1 mm
    (4.45 to 4.85 in.)
    107.8 to 117.8 mm
    (4.244 to 4.638 in.)

    If the pedal height is incorrect, adjust it.



  1. Adjust the brake pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Loosen the push rod lock nut.

    4. Adjust the pedal height by turning the pedal push rod.

      Pedal height from floor panel:
      w/ ABS
      w/o ABS
      113.1 to 123.1 mm
      (4.45 to 4.85 in.)
      107.8 to 117.8 mm
      (4.244 to 4.638 in.)

    5. Tighten the push rod lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    6. F049043E01
    7. Insert the stop light switch into the adjuster until it just touches the brake pedal.

      NOTICE:
      Do not depress the brake pedal.



    8. F049044E08
    9. Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      The turning torque for installing the stop light switch:

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    10. Check the stop light switch clearance.

      Stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)

    11. Connect the connector to the stop light switch.



    F048932E01
  1. Inspect the brake pedal free play.

    1. Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.

    2. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

      Pedal free play:
      1.0 to 6.0 mm (0.039 to 0.236 in.)

      If incorrect, troubleshoot the brake system.



    R000934E02
  1. Inspect the brake pedal reserve distance.

    1. Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.

      Pedal reserve distance from floor panel at 294 N (30 kgf, 66.1 lbf):
      w/ ABS
      w/o ABS
      More than 78 mm (3.07 in.)
      More than 70 mm (2.75 in.)

      HINT:
      Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.

      If incorrect, troubleshoot the brake system.



9. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    G028410E01
  1. Connect all the connectors and clamp the wire harnesses onto the steering column assembly bracket.

  1. Align the matchmarks on steering intermediate shaft assembly No. 2 and the steering sliding yoke and provisionally install them with bolt C.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



10. INSTALL COLUMN HOLE COVER SILENCER SHEET


    A116501
  1. Install the column hole cover plate with the 2 clips.

  1. Install the floor carpet.



11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY



12. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY



13. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY



14. INSTALL FRONT PILLAR GARNISH RH



15. INSTALL FRONT PILLAR GARNISH LH



16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH



17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH



18. INSTALL COMBINATION METER ASSEMBLY



19. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1



20. INSTALL INSTRUMENT PANEL FINISH PANEL END RH



21. INSTALL INSTRUMENT PANEL FINISH PANEL END LH



22. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL


B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.



23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



24. INSPECT SRS WARNING LIGHT
(Click here)