Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › ECM (for Sedan)

ECM (for Sedan) > INSTALLATION



1. INSTALL ECM BRACKET NO. 2


A115388
  1. Install ECM bracket No. 2 with the 2 screws.



2. INSTALL ECM BRACKET


A115387
  1. Install the ECM bracket with the 2 screws.



3. INSTALL ECM


A115386
  1. Install the ECM with the bolt and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 ECM connectors.



    A115385
  1. Install the 2 lock knobs and harness clamp.



4. INSTALL COWL TOP PANEL OUTER


    A133328
  1. Install the cowl top panel outer and install the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    A133326
  1. Install the cowl top panel outer center bracket and install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    A133322
  1. Connect the wire harness and engage the claw.



5. INSTALL FRONT AIR SHUTTER SEAL


    A133324
  1. Install the front air shutter seal and engage the 3 claws.



6. INSTALL FRONT WIPER MOTOR AND LINK


    E127840
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



7. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127839
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127838
  1. Engage the 8 hooks and the 4 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 3 clips.



8. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E129651
  1. Engage the 3 claws and install the cowl side ventilator sub-assembly LH.



9. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



11. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E129694E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



12. INSTALL FRONT WIPER ARM HEAD CAP


    E127841
  1. Engage the claw and install the 2 front wiper arm head caps.



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



14. PERFORM INITIALIZATION
(Click here)