Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door)

REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door) > INSTALLATION


HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. INSTALL SEAT BELT HOLE SEAL
  1. Engage the 2 claws to install the seat belt hole seal.



2. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY


    B108365E01
  1. Check the angle of inclination required to lock the retractor.
    Text in Illustration 
    *a
    Lock
    *b
    Unlock

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the rear seat 3 point type outer belt assembly.

  1. Engage the 2 hooks to install the rear seat 3 point type outer belt assembly.

  1. Install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Connect the shoulder anchor part of the rear seat 3 point type outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Connect the floor anchor part of the rear seat 3 point type outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the rear seat 3 point type outer belt assembly installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the rear seat 3 point type outer belt assembly.

  1. Remove the bolt to disconnect the floor anchor part of the rear seat 3 point type outer belt assembly.



3. INSTALL ROOF SIDE INNER GARNISH
  1. Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish.

  1. Engage the 4 clips and install the roof side inner garnish.



4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 3 clips.

  1. Engage the guide and the 4 claws and install the deck trim side panel.

  1. Install the 3 screws.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

HINT:
Use the same procedure as for the RH side.



6. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY
  1. Engage the 2 claws and install the rear seat 3 point type outer belt.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



7. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


    B284353E01
  1. Align the paint mark on the rear door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Flange Position

    Paint Mark:
    Area
    Color
    RH Side
    Purple
    LH Side
    Pink

    NOTICE:
    After installation, check that the corners fit correctly.



8. INSTALL REAR DOOR SCUFF PLATE
  1. Engage the guide and the 5 claws and install the rear door scuff plate.



9. INSTALL REAR FLOOR FINISH PLATE
  1. Engage the 4 guides and the 4 claws to install the rear floor finish plate.



10. INSTALL JACK HANDLE (for RH Side)


11. INSTALL NO. 2 ROOM LIGHT ASSEMBLY (for LH Side)


    E222046
  1. Connect the connector.

  1. Engage the claw to install the No. 2 room light assembly.



12. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board.



13. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


14. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


15. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)