Home › Vehicle Interior › SEAT BELT › CHILD RESTRAINT SEAT ANCHOR BRACKET (for Hatchback 3 Door)

CHILD RESTRAINT SEAT ANCHOR BRACKET (for Hatchback 3 Door) > INSTALLATION



1. INSTALL REAR SEATBACK CENTER HINGE SUB-ASSEMBLY (for 60/40 Split Seat Type)


    B282726
  1. Temporarily install the rear seatback center hinge sub-assembly with the bolt shown in the illustration.



    B282725E01
  1. Install the bolt and tighten the 2 bolts in the order shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH


    B282727
  1. Temporarily install the child restraint seat anchor bracket sub-assembly RH with the bolt shown in the illustration.



    B282724E01
  1. Install the 2 bolts and tighten the 3 bolts in the order shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    B282728
  1. Temporarily install the child restraint seat anchor bracket sub-assembly LH with the bolt shown in the illustration.



    B282723E01
  1. Install the 2 bolts and tighten the 3 bolts in the order shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 3 clips and the 3 claws and install the deck trim side panel.

  1. Install the 3 screws.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

HINT:
Use the same procedure as for the RH side.



6. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
  1. Engage the 2 claws and install the rear seat 3 point type outer belt.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



7. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



8. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
  1. Engage the 8 clips and the 10 claws.

  1. Engage the 3 guides and install the quarter trim panel.



9. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



10. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
  1. Install the floor end of the front seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Engage the 2 claws and install the anchor cover.



11. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



12. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B284341E01
  1. Align the paint mark on the front door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Flange Position

    Paint Mark:
    Area
    Color
    RH Side
    Yellow
    LH Side
    White

    NOTICE:
    After installation, check that the corners fit correctly.



13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



14. INSTALL FRONT DOOR SCUFF PLATE RH
  1. Engage the 8 claws and install the front door scuff plate.



15. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



16. INSTALL REAR FLOOR FINISH PLATE
  1. Engage the 4 guides and the 4 claws to install the rear floor finish plate.



17. INSTALL JACK HANDLE (for RH Side)


18. INSTALL NO. 2 ROOM LIGHT ASSEMBLY


    E222046
  1. Connect the connector.

  1. Engage the claw to install the No. 2 room light assembly.



19. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board.



20. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


21. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


22. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)