Home › Drivetrain ยท AXLE AND DIFFERENTIAL › FRONT AXLE HUB (for Hatchback)

FRONT AXLE HUB (for Hatchback) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side as for the LH side.
  2. The procedure listed below is for the LH side.



1. REMOVE FRONT WHEEL


2. REMOVE FRONT AXLE SHAFT NUT


C236996E01
  1. Using SST and a hammer, release the staked part of the front axle shaft nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the front axle shaft nut.
    4. Do not damage the threads of the front drive shaft.

  1. Using a deep socket wrench 30 mm, remove the front axle shaft nut.



3. SEPARATE FRONT SPEED SENSOR (w/ ABS)


    C107502
  1. Remove the bolt and separate the front speed sensor and the front flexible hose.



    C112274
  1. Remove the bolt and separate the front speed sensor from the front axle assembly.

    NOTICE:
    1. Keep the front speed sensor tip and installation portion free of foreign matter.
    2. Remove the front speed sensor without turning it from its original installation angle.



4. REMOVE FRONT FLEXIBLE HOSE (w/o ABS)
  1. Remove the bolt and separate the front flexible hose.



5. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY


    C085618
  1. Remove the 2 bolts and separate the front disc brake caliper assembly.

    NOTICE:
    Hang the front disc brake caliper assembly using a piece of string or the equivalent.



6. REMOVE FRONT DISC


    C108932E02
  1. Place matchmarks on the disc and axle hub and remove the disc.
    Text in Illustration 
    *a
    Matchmark



7. SEPARATE TIE ROD END SUB-ASSEMBLY


    C265509
  1. Remove the cotter pin and the castle nut.



    C172757E03
  1. Install SST to the threaded section of the tie rod end sub-assembly.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the tie rod end and SST are aligned.



  1. Using SST, separate the tie rod end sub-assembly from the front axle assembly.


    C249935E02


    Text in Illustration 
    *1
    Center Nut
    -
    -
    *a
    String
    *b
    Molybdenum Grease Application Area
    *c
    Place the wrench here
    *d
    Turn
    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Apply molybdenum grease to the bolt threads and the tip of SST.
    2. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    3. Install SST so that A and B are parallel.
    4. Be sure to place the wrench on the part indicated in the illustration.
    5. Do not damage the ball joint dust cover.
    6. Do not damage the front disc brake dust cover.



8. SEPARATE FRONT LOWER SUSPENSION ARM


    C107513
  1. Remove the clip and the castle nut.



    C172759E05
  1. Install SST to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the lower ball joint and SST are aligned.



  1. Using SST, separate the front lower suspension arm from the front axle assembly.


    C265987E01


    Text in Illustration 
    *1
    Center Nut
    -
    -
    *a
    String
    *b
    Molybdenum Grease Application Area
    *c
    Place the wrench here
    *d
    Turn
    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Apply molybdenum grease to the bolt threads and the tip of SST.
    2. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    3. Install SST so that A and B are parallel.
    4. Be sure to place the wrench on the part indicated in the illustration.
    5. Do not damage the lower ball joint dust cover.
    6. Do not damage the drive shaft outboard joint boots.
    7. Do not damage the front disc brake dust cover.



9. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    C235026
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    Using a socket hexagon wrench 6 mm to hold the stud.



10. REMOVE FRONT AXLE ASSEMBLY
  1. Using a plastic hammer, tap the end of the drive shaft and separate the fitting between the drive shaft and front axle assembly.

    NOTICE:
    Do not hammer the threads of the drive shaft.

    HINT:
    If it is difficult to separate the fitting, tap the end of the drive shaft with a brass bar and hammer.



    C125277
  1. Remove the 2 nuts, 2 bolts and the front axle assembly.

    NOTICE:
    1. Do not damage the lower ball joint.
    2. Do not damage the threads of the drive shaft.
    3. Do not damage the front speed sensor rotor.
    4. Do not damage the drive shaft outboard joint boot.
    5. Suspend the drive shaft with a piece of string or equivalent.

    HINT:
    Keep the bolt from rotating while turning the nut.



11. REMOVE FRONT AXLE HUB HOLE SNAP RING


    C202595
  1. Using snap ring pliers, remove the axle hub hole snap ring.

    NOTICE:
    When removing the hole snap ring, do not damage the magnetic rotor surface.



12. REMOVE FRONT AXLE HUB SUB-ASSEMBLY


    C057871E01
  1. Fix the steering knuckle in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Using SST, remove the axle hub.

    SST
    09520-00031  



    C202597E02
  1. Using SST, remove the axle hub bearing inner race.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
    09950-60010   (09951-00370)

    NOTICE:
    1. When removing the inner race, it the axle hub is damaged, replace the axle hub with a new one.
    2. Apply a small amount of grease to the threads and tip of SST before use.



13. REMOVE FRONT AXLE HUB BEARING
(Click here)