Home › Engine / Hybrid System › 1NZ-FE FUEL › FUEL PUMP (for Sedan)

FUEL PUMP (for Sedan) > REMOVAL

for Preparation Click here



1. REMOVE REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for 60/40 Split Seat Type)


    B134922
  1. Hold the front edge of the rear seat cushion cover pad and lift it up, as shown in the illustration, to disengage the 2 hooks.

    NOTICE:
    Hold the area around the hooks so as to avoid deforming the rear seat cushion frame.

  1. Pass the rear seat inner belt through the slit in the rear seat cushion cover pad, disengage the hook between the rear seat cushion cover pad and the rear seatback, and remove the rear seat cushion cover pad.



2. REMOVE REAR FLOOR SERVICE HOLE COVER


A302976E01
  1. Using a clip remover with tip wrapped with protective tape, remove the rear floor service hole cover from the vehicle.
    Text in Illustration 
    *a
    Clip Remover
    *b
    Protective Tape
    *c
    Butyl Tape



    A115462
  1. Disconnect the fuel pump connector.



3. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


5. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


A115463
  1. Widen the tip of the tube joint clip and pull out the clip in the direction indicated by the arrow.

  1. Disconnect the fuel tank main tube sub-assembly.

    NOTICE:
    1. Keep the O-ring free of any foreign matter, as it becomes contaminated easily.
    2. Do not use any tools in this procedure.
    3. Do not forcefully bend or twist the tube.
    4. Put the tube in a plastic bag to prevent damage and contamination.
    5. If the fuel suction plate and tube are stuck together, pinch the tube and turn it carefully to disconnect them.
    6. Do not damage the tube joint clip. If the tube joint clip is damaged, replace it.



6. DISCONNECT FUEL TANK VENT HOSE


    A264595E01
  1. Release the retainer as shown in the illustration and disconnect the fuel tank vent hose.
    Text in Illustration 
    *1
    Retainer
    V100135
    Push
    V100136
    Pull

    NOTICE:
    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.
    2. The quick connector seals with an O-ring. Ensure that there is no damage or foreign matter on the contact surface.
    3. Do not use any tools.
    4. Do not bend or twist the tubes.
    5. Protect the contact surface by covering it with a plastic bag.
    6. If the connector is stuck, push and pull on the parts to separate them.



7. REMOVE FUEL PUMP GAUGE RETAINER

NOTICE:
Before performing the work, cover the connector of the fuel suction tube assembly and the tube joint with a plastic bag to prevent foreign matter from entering, and then clean off any dirt or other foreign matter.



    A305546E01
  1. Install SST to the fuel pump gauge retainer.

    SST
    09808-14030   (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

    1. Temporarily install plate and claw to the fuel pump gauge retainer.

    2. Press claw against the rib of the fuel pump gauge retainer, and tighten bolt.

    3. Install SST (handle).



    A247498E02
  1. While making sure that SST does not rise up, slowly turn handle and loosen the fuel pump gauge retainer.

    NOTICE:
    1. Be careful not to apply excessive downward force to SST, as this may damage the fuel pump or fuel tank.
    2. Turning SST at an angle may cause it to slip off of the fuel pump gauge retainer, so be sure SST is horizontal when turning.
    3. To prevent damage to parts, do not turn SST too vigorously.
    4. If SST slips off of the fuel pump gauge retainer, loosen SST (bolt) and install SST again.

  1. While holding down the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



8. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
  1. Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

    NOTICE:
    1. Be careful not to bend the arm of the fuel sender gauge assembly.
    2. When installing or removing the fuel suction tube with pump and gauge assembly, be careful of fuel splashing.



9. REMOVE FUEL SUCTION TUBE SET GASKET


    A247501
  1. Remove the fuel suction tube set gasket from the fuel tank assembly.