LOWER INSTRUMENT PANEL (for Hatchback) > REMOVAL |

| 1. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
| 2. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Disengage the claw and separate the glove compartment door stopper from the glove compartment door.
Slightly flex the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
![]() |
Pull the glove compartment door out horizontally to disengage the 2 hinges and 3 guides and remove the glove compartment door.
| *a | Hinge |
| *b | Guide |
| 3. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Remove the 2 <A> screws.
Disengage the claw and the guide and remove the instrument panel under cover.
| 4. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL |
![]() |
Disengage the 5 clips and the 2 claws and remove the instrument panel finish panel.
| 5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag) |
![]() |
Disengage the 2 clips and the 5 claws and remove the instrument panel finish panel.
| 6. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag) |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Remove the 4 bolts.
| *1 | Protective Tape |
| *2 | Locking Button |
Disengage the 6 claws to separate the lower No. 1 instrument panel airbag assembly.
Using a screwdriver with its tip wrapped in protective tape, release the locking button.
Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
| 7. REMOVE STEREO OPENING COVER WITH BRACKET (for TMC Made) |
![]() |
Remove the 4 screws and the stereo opening cover with bracket.
| 8. REMOVE STEREO OPENING COVER WITH BRACKET (for TMMF Made) |
![]() |
Remove the 4 screws and the stereo opening cover with bracket.
| 9. SEPARATE AIR CONDITIONING PANEL ASSEMBLY |
![]() |
Disengage the claw and 7 clips.
![]() |
Disconnect the connectors and separate the air conditioning panel.
| 10. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and disconnect the defroster damper control cable.
| 11. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and disconnect the air mix damper control cable.
| 12. REMOVE REAR CONSOLE BOX ASSEMBLY |
| 13. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the 3 claws and separate the hood lock control lever.
| 14. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and disconnect the DLC3 connector.
Disconnect the clamps and connectors.
for TMC Made:

Remove the 6 <B> or <C> bolts, <D> or <E> screw, 2 <F> or <H> or <I> bolts, and bolt from the lower instrument panel.
for TMMF Made:

Remove the 6 <B> or <C> bolts, <D> or <E> screw, 2 <F> bolts, and bolt from the lower instrument panel.
Disengage the 10 guides and remove the lower instrument panel.
