Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Hatchback)

CAN COMMUNICATION SYSTEM (for Hatchback) > TERMINALS OF ECU


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR


  1. NO. 1 JUNCTION CONNECTOR


    E217688E09


    Text in Illustration 
    *a
    to ECM
    *b
    to Skid Control ECU (Brake Actuator Assembly) (w/ ABS)
    *c
    to Main Body ECU (Multiplex Network Body ECU)
    *d
    to Power Steering ECU Assembly
    *e
    to DLC3
    *f
    to No. 2 Junction Connector

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    A73-9 (CANH)
    L
    ECM
    A73-20 (CANL)
    W
    A73-10 (CANH)
    G
    Skid Control ECU (Brake Actuator Assembly)*1
    A73-21 (CANL)
    W
    D146-1 (CANH)
    R
    Main Body ECU (Multiplex Network Body ECU)
    D146-12 (CANL)
    W
    D146-2 (CANH)
    LG
    Power Steering ECU Assembly
    D146-13 (CANL)
    W
    D146-3 (CANH)
    GR
    DLC3
    D146-14 (CANL)
    W
    D146-4 (CANH)
    SB
    No. 2 Junction Connector
    D146-15 (CANL)
    W
    1. *1: w/ ABS



  2. NO. 2 JUNCTION CONNECTOR


    E217689E06


    Text in Illustration 
    *a
    to Steering Angle Sensor (Spiral Cable Sub-assembly)*1
    *b
    to Airbag Sensor Assembly
    *c
    to Combination Meter Assembly
    *d
    to Air Conditioning Amplifier Assembly
    *e
    to No. 1 Junction Connector
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    D147-1 (CANH)
    P
    Steering Angle Sensor (Spiral Cable Sub-assembly)*1
    D147-12 (CANL)
    W
    D147-4 (CANH)
    B
    Airbag Sensor Assembly
    D147-15 (CANL)
    W
    D147-7 (CANH)
    G
    Combination Meter Assembly
    D147-18 (CANL)
    W
    D147-8 (CANH)
    V
    Air Conditioning Amplifier Assembly
    D147-19 (CANL)
    W
    D147-10 (CANH)
    SB
    No. 1 Junction Connector
    D147-21 (CANL)
    W
    1. *1: w/ VSC


CHECK DLC3

C188081E19

  1. Turn the ignition switch off.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D102-6 (CANH) - D102-14 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    D102-6 (CANH) - D102-16 (BAT)
    GR - BE
    Ignition switch off
    6 kΩ or higher
    D102-14 (CANL) - D102-16 (BAT)
    W - BE
    Ignition switch off
    6 kΩ or higher
    D102-6 (CANH) - D102-4 (CG)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    D102-14 (CANL) - D102-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK ECM

E217715E02

  1. Disconnect the A72 and C51 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A72-13 (CANH) - A72-26 (CANL)
    L - W
    Ignition switch off
    108 to 132 Ω
    A72-13 (CANH) - A72-2 (+B)
    L - B
    Ignition switch off
    6 kΩ or higher
    A72-26 (CANL) - A72-2 (+B)
    W - B
    Ignition switch off
    6 kΩ or higher
    A72-13 (CANH) - C51-16 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    A72-26 (CANL) - C51-16 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (2 Connector Type)

E231936E08


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Multiplex Network Body ECU)
  1. Disconnect the D143 main body ECU (multiplex network body ECU) connector.

  2. Disconnect the 3B and 3C instrument panel junction block assembly connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D143-14 (CANH) - D143-13 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D143-14 (CANH) - 3C-21
    R - L
    Ignition switch off
    6 kΩ or higher
    D143-13 (CANL) - 3C-21
    W - L
    Ignition switch off
    6 kΩ or higher
    D143-14 (CANH) - 3B-8
    R - W-B
    Ignition switch off
    200 Ω or higher
    D143-13 (CANL) - 3B-8
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (1 Connector Type)

E217205E04


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Multiplex Network Body ECU)
  1. Disconnect the D143 main body ECU (multiplex network body ECU) connector.

  2. Disconnect the 3B and 3C instrument panel junction block assembly connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D143-14 (CANH) - D143-13 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D143-14 (CANH) - 3C-21
    R - L
    Ignition switch off
    6 kΩ or higher
    D143-13 (CANL) - 3C-21
    W - L
    Ignition switch off
    6 kΩ or higher
    D143-14 (CANH) - 3B-8
    R - W-B
    Ignition switch off
    200 Ω or higher
    D143-13 (CANL) - 3B-8
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK COMBINATION METER ASSEMBLY

E217699E03

  1. Disconnect the D100 combination meter assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D100-32 (CANH) - D100-31 (CANL)
    G - W
    Ignition switch off
    108 to 132 Ω
    D100-32 (CANH) - D100-40 (B)
    G - L
    Ignition switch off
    6 kΩ or higher
    D100-31 (CANL) - D100-40 (B)
    W - L
    Ignition switch off
    6 kΩ or higher
    D100-32 (CANH) - D100-21 (ET)
    G - W-B
    Ignition switch off
    200 Ω or higher
    D100-31 (CANL) - D100-21 (ET)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (w/ ABS)

E186733E07


Text in Illustration 
*A
w/ VSC
*B
w/o VSC
  1. Disconnect the A70*1 or A71*2 skid control ECU (brake actuator assembly) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A70-25 (CANH) - A70-14 (CANL)*1
    A71-25 (CANH) - A71-14 (CANL)*2
    G - W
    Ignition switch off
    54 to 69 Ω
    A70-25 (CANH) - A70-12 (+BS)*1
    A71-25 (CANH) - A71-12 (+BS)*2
    G - W
    Ignition switch off
    6 kΩ or higher
    A70-14 (CANL) - A70-12 (+BS)*1
    A71-14 (CANL) - A71-12 (+BS)*2
    W - W
    Ignition switch off
    6 kΩ or higher
    A70-25 (CANH) - A70-1 (GND1)*1
    A71-25 (CANH) - A71-1 (GND1)*2
    G - W-B
    Ignition switch off
    200 Ω or higher
    A70-14 (CANL) - A70-1 (GND1)*1
    A71-14 (CANL) - A71-1 (GND1)*2
    W - W-B
    Ignition switch off
    200 Ω or higher
    *1: w/ VSC
    *2: w/o VSC


CHECK AIRBAG SENSOR ASSEMBLY

E221476E02


Text in Illustration 
*A
w/o VSC
*B
w/ VSC
  1. Disconnect the D112 airbag sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D112-13 (CANH) - D112-22 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    D112-13 (CANH) - D102-16 (BAT)
    B - BE
    Ignition switch off
    6 kΩ or higher
    D112-22 (CANL) - D102-16 (BAT)
    W - BE
    Ignition switch off
    6 kΩ or higher
    D112-13 (CANH) - D102-4 (CG)
    B - W-B
    Ignition switch off
    200 Ω or higher
    D112-22 (CANL) - D102-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (w/ VSC)

E186735E03

  1. Disconnect the D122 steering angle sensor (spiral cable sub-assembly) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D122-4 (CANH) - D122-3 (CANL)
    P - W
    Ignition switch off
    54 to 69 Ω
    D122-4 (CANH) - D122-6 (BAT)
    P - SB
    Ignition switch off
    6 kΩ or higher
    D122-3 (CANL) - D122-6 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher
    D122-4 (CANH) - D122-2 (ESS)
    P - BR
    Ignition switch off
    200 Ω or higher
    D122-3 (CANL) - D122-2 (ESS)
    W - BR
    Ignition switch off
    200 Ω or higher


CHECK POWER STEERING ECU ASSEMBLY

C231648E02

  1. Disconnect the A68 and D104 power steering ECU assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D104-7 (CANH) - D104-8 (CANL)
    LG - W
    Ignition switch off
    54 to 69 Ω
    D104-7 (CANH) - A68-1 (PIG)
    LG - W
    Ignition switch off
    6 kΩ or higher
    D104-8 (CANL) - A68-1 (PIG)
    W - W
    Ignition switch off
    6 kΩ or higher
    D104-7 (CANH) - A68-2 (PGND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    D104-8 (CANL) - A68-2 (PGND)
    W - W-B
    Ignition switch off
    200 Ω or higher


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

E231185E01

  1. Disconnect the D130 air conditioning amplifier assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D130-8 (TX+) - D130-9 (TX-)
    V - W
    Ignition switch off
    54 to 69 Ω
    D130-8 (TX+) - D102-16 (BAT)
    V - BE
    Ignition switch off
    6 kΩ or higher
    D130-9 (TX-) - D102-16 (BAT)
    W - BE
    Ignition switch off
    6 kΩ or higher
    D130-8 (TX+) - D130-23 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    D130-9 (TX-) - D130-23 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher