DTC B1612/83 Lost Communication with Front Airbag Sensor RH |
DTC B1613/83 Front Airbag Sensor RH Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1612/83 B1613/83 | When one of following conditions is met:
|
|

| 1.CHECK DTC |
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and the front airbag sensor RH.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH.
Check that the connectors (on the airbag sensor assembly side and front airbag sensor RH side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT |

| *1 | Front Airbag Sensor RH | *2 | Airbag Sensor Assembly |
| *3 | Connector E | *4 | Connector B |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector (to Front Airbag Sensor RH) | *b | Rear view of wire harness connector (to Airbag Sensor Assembly) |
Connect the cable to the negative battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A56-2 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| A56-1 (-SR) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 29 and 27 of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A56-2 (+SR) - A56-1 (-SR) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A56-2 (+SR) - A56-1 (-SR) | Always | 1 MΩ or higher |
| A56-2 (+SR) - Body ground | Always | 1 MΩ or higher |
| A56-1 (-SR) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FRONT AIRBAG SENSOR RH |
![]() |
Connect the connectors to the airbag sensor assembly.
Interchange the front airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1612/83, B1613/83, B1617/84 and B1618/84 are not output | A |
| DTC B1617/84 or B1618/84 is output | B |
| DTC B1612/83 or B1613/83 is output | C |
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the front airbag sensor RH and front airbag sensor LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||
| 6.CHECK INSTRUMENT PANEL WIRE (AIRBAG SENSOR ASSEMBLY - ENGINE ROOM MAIN WIRE) |

| *1 | Front Airbag Sensor RH | *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *5 | Connector C | *6 | Connector B |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector (to Engine Room Main Wire) | *b | Rear view of wire harness connector (to Airbag Sensor Assembly) |
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| AD6-1 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| AD6-2 (-SR) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminal -SR and +SR of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AD6-1 (+SR) - AD6-2 (-SR) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AD6-1 (+SR) - AD6-2 (-SR) | Always | 1 MΩ or higher |
| AD6-1 (+SR) - Body ground | Always | 1 MΩ or higher |
| AD6-2 (-SR) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||