DTC B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete |
DTC B1617/84 Lost Communication with Front Airbag Sensor LH |
| DTC Code | Detection Condition | Trouble Area |
| B1608/84 B1617/84 | When one of following conditions is met:
|
|

| 1.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH.
Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged.
|
| ||||
| OK | |
| 3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A12-2 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| A12-1 (-SL) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A12-2 (+SL) - A12-1 (-SL) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A12-2 (+SL) - A12-1 (-SL) | Always | 1 MΩ or higher |
| A12-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| A12-1 (-SL) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK FRONT AIRBAG SENSOR LH |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the front airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1603/83, B1612/83, B1608/84 and B1617/84 are not output | A |
| DTC B1603/83 or B1612/83 is output | B |
| DTC B1608/84 or B1617/84 is output | C |
|
| ||||
|
| ||||
| C | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE ASSEMBLY (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE) |

Disconnect the instrument panel wire connector from the engine room main wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| AD1-3 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| AD1-4 (-SL) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AD1-3 (+SL) - AD1-4 (-SL) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AD1-3 (+SL) - AD1-4 (-SL) | Always | 1 MΩ or higher |
| AD1-3 (+SL) - Body ground | Always | 1 MΩ or higher |
| AD1-4 (-SL) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||