Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback 5 Door)

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback 5 Door) > REMOVAL



1. REMOVE DECK BOARD ASSEMBLY


    B272608
  1. Remove the deck board.



2. REMOVE FRONT SEAT ASSEMBLY (for Driver Side)
(Click here)


3. REMOVE FRONT SEAT ASSEMBLY (for Front Passenger Side)
(Click here)


4. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


5. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


6. REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


7. REMOVE REAR CONSOLE BOX ASSEMBLY
(Click here)


8. REMOVE FRONT DOOR SCUFF PLATE RH


    B272611
  1. Disengage the 8 claws and remove the front door scuff plate.



9. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



10. REMOVE COWL SIDE TRIM BOARD RH


    B284314
  1. Remove the clip.

  1. Disengage the clip and remove the cowl side trim board.



11. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



12. REMOVE REAR DOOR SCUFF PLATE RH


    B272618
  1. Disengage the 5 claws and guide and remove the rear door scuff plate.



13. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



14. REMOVE REAR FLOOR FINISH PLATE


    B272624
  1. Disengage the 4 claws and 4 guides and remove the rear floor finish plate.



15. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side .



16. SEPARATE REAR DOOR OPENING TRIM WEATHERSTRIP
  1. Separate the rear door opening trim weatherstrip.



17. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    E222045E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connector and remove the No. 2 room light assembly.



18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side .



19. REMOVE JACK COVER


20. REMOVE JACK ASSEMBLY


21. REMOVE NO. 2 FLOOR CARPET HOOK

HINT:
Use the same procedure for both sides.



    B319063
  1. Rotate the No. 2 floor carpet hook 90° in the direction shown by the arrow in the illustration, disengage the hook and remove the No. 2 floor carpet hook.



22. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Disengage the 6 clamps.

  1. Remove the clip and front floor carpet assembly.



23. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B284622
  1. Remove the bolt.

  1. Disengage guide and separate the fuel lid lock open lever sub-assembly in the direction indicated by the arrow as shown in the illustration.



    B284621
  1. Disengage the guide and separate the fuel lid lock control cable sub-assembly.



24. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


    B266731
  1. Disengage the 2 claws and separate the fuel lid lock control cable sub-assembly.



  1. Disengage the 4 clamps and remove the fuel lid lock control cable sub-assembly as shown in the illustration.


    B284618E03


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Wire Harness Clamp



25. REMOVE FUEL FILLER OPENING LID LOCK RETAINER


    B266728E01
  1. Rotate the fuel filler opening lid lock retainer by 90° and disengage the 2 claws A from the 2 slits as shown in the illustration.
    Text in Illustration 
    *1
    Claw A
    *a
    Slit
    *b
    Rotate



    B266729E01
  1. Rotate the fuel filler opening lid lock retainer by another 90° and remove it by disengaging the 2 claws B from the 2 slits as shown in the illustration.
    Text in Illustration 
    *1
    Claw B
    *a
    Slit
    *b
    Rotate