Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback 3 Door)

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback 3 Door) > REMOVAL



1. REMOVE DECK BOARD ASSEMBLY


    B272608
  1. Remove the deck board.



2. REMOVE FRONT SEAT ASSEMBLY (for Driver Side)
(Click here)


3. REMOVE FRONT SEAT ASSEMBLY (for Front Passenger Side)
(Click here)


4. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


5. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


6. REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


7. REMOVE REAR CONSOLE BOX
(Click here)


8. REMOVE FRONT DOOR SCUFF PLATE RH


    B284313
  1. Disengage the 8 claws and remove the front door scuff plate.



9. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



10. REMOVE COWL SIDE TRIM BOARD RH


    B284314
  1. Remove the clip.

  1. Disengage the clip and remove the cowl side trim board.



11. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



12. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.



13. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.



14. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH


    B284316
  1. Disengage the 2 claws and remove the anchor cover.



    B284317
  1. Remove the bolt and separate the front seat outer belt.



15. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



16. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH


    B284318
  1. Disengage the 8 clips and 10 claws.

  1. Disengage the 3 guides and remove the quarter trim panel.



17. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



18. REMOVE REAR FLOOR FINISH PLATE


    B272624
  1. Disengage the 4 claws and 4 guides and remove the rear floor finish plate.



19. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH


    B284323
  1. Remove the bolt.

  1. Disengage the 2 claws and separate the rear seat 3 point type outer belt.



20. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



21. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    E222045E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connector and remove the No. 2 room light assembly.



22. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side .



23. REMOVE JACK COVER


24. REMOVE JACK ASSEMBLY


25. REMOVE NO. 2 FLOOR CARPET HOOK

HINT:
Use the same procedure for both sides.



    B319063
  1. Rotate the No. 2 floor carpet hook 90° in the direction shown by the arrow in the illustration, disengage the hook and remove the No. 2 floor carpet hook.



26. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Disengage the 6 clamps.

  1. Remove the clip and front floor carpet assembly.



27. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B284622
  1. Remove the bolt.

  1. Disengage the guide and separate the fuel lid lock open lever sub-assembly in the direction indicated by the arrow as shown in the illustration.



    B284621
  1. Disengage the guide and separate the fuel lid lock control cable sub-assembly.



28. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


    B266731
  1. Disengage the 2 claws and separate the fuel lid lock control cable sub-assembly.



  1. Disengage the 4 clamps and remove the fuel lid lock control cable sub-assembly as shown in the illustration.


    B284620E02


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Wire Harness Clamp



29. REMOVE FUEL FILLER OPENING LID LOCK RETAINER


    B266728E01
  1. Rotate the fuel filler opening lid lock retainer by 90° and disengage the 2 claws A from the 2 slits as shown in the illustration.
    Text in Illustration 
    *1
    Claw A
    *a
    Slit
    *b
    Rotate



    B266729E01
  1. Rotate the fuel filler opening lid lock retainer by another 90° and remove it by disengaging the 2 claws B from the 2 slits as shown in the illustration.
    Text in Illustration 
    *1
    Claw B
    *a
    Slit
    *b
    Rotate