Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Hatchback)

AIR CONDITIONING SYSTEM (for Hatchback) > Heater Control Switch Circuit


DESCRIPTION

The No. 3 heater control sub-assembly (A/C switch*1, A/C LED*1, MAX HOT switch*2) is powered through the A/C fuse. The No. 3 heater control sub-assembly (A/C switch*1, A/C LED*1, MAX HOT switch*2) transmits operational signals of each switch to the air conditioning amplifier assembly.
  1. *1: w/ Cooler
  2. *2: w/ PTC Heater

WIRING DIAGRAM


E231016E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedures.

1.INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY (A/C SWITCH, A/C LED, MAX HOT SWITCH)
  1. Inspect the No. 3 heater control sub-assembly (A/C switch*1, A/C LED*1, MAX HOT switch*2) (Click here).

    1. *1: w/ Cooler
    2. *2: w/ PTC Heater



NG
REPLACE NO. 3 HEATER CONTROL SUB-ASSEMBLY (A/C SWITCH, A/C LED, MAX HOT SWITCH) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (NO. 3 HEATER CONTROL SUB-ASSEMBLY - IG1 NO. 1 RELAY)


    E229325E01
  1. Disconnect the D127 No. 3 heater control sub-assembly (A/C switch*1, A/C LED*1, MAX HOT switch*2) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D127-2 (B) - Body ground*1
    Ignition switch ON
    11 to 14 V
    D127-2 (B) - Body ground*1
    Ignition switch off
    Below 1 V
    D127-7 (B) - Body ground*2
    Ignition switch ON
    11 to 14 V
    D127-7 (B) - Body ground*2
    Ignition switch off
    Below 1 V

    1. *1: w/ Cooler
    2. *2: w/ PTC Heater
    Text in Illustration 
    *A
    w/ Cooler
    *B
    w/ PTC Heater
    *a
    Front view of wire harness connector
    (to No. 3 Heater Control Sub-Assembly (A/C Switch, A/C LED, MAX HOT Switch))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (NO. 3 HEATER CONTROL SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the D127 No. 3 heater control sub-assembly (A/C switch*1, A/C LED*1, MAX HOT switch*2) connector.

  1. Disconnect the D130 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D127-3 (A/C) - D130-2 (A/C)*1
    Always
    Below 1 Ω
    D127-4 (AIND) - D130-16 (LED)*1
    Always
    Below 1 Ω
    D127-8 (E) - D130-3 (HEAT)*2
    Always
    Below 1 Ω
    D127-3 (A/C) - Body ground*1
    Always
    10 kΩ or higher
    D127-4 (AIND) - Body ground*1
    Always
    10 kΩ or higher
    D127-8 (E) - Body ground*2
    Always
    10 kΩ or higher

    1. *1: w/ Cooler
    2. *2: w/ PTC Heater



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)